| /programy/C/PIC/test/C16F873/blik/main.c |
|---|
| 0,0 → 1,31 |
| #include ".\main.h" |
| void main() |
| { |
| int8 ble; |
| setup_adc_ports(NO_ANALOGS); |
| setup_adc(ADC_OFF); |
| setup_spi(FALSE); |
| setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
| setup_timer_1(T1_DISABLED); |
| setup_timer_2(T2_DISABLED,0,1); |
| setup_comparator(NC_NC_NC_NC); |
| setup_vref(FALSE); |
| output_low(PIN_C1); |
| While(true) |
| { |
| output_c(ble++); |
| delay_ms(100); |
| Output_high(PIN_B2); |
| Delay_ms(100); |
| Output_low(PIN_B2); |
| Delay_ms(100); |
| } |
| } |
| /programy/C/PIC/test/C16F873/blik/main.h |
|---|
| 0,0 → 1,15 |
| #include <16F876A.h> |
| #device adc=8 |
| #FUSES NOWDT //No Watch Dog Timer |
| #FUSES HS //Crystal osc <= 4mhz |
| #FUSES NOPUT //No Power Up Timer |
| #FUSES NOPROTECT //Code not protected from reading |
| #FUSES NODEBUG //No Debug mode for ICD |
| #FUSES NOBROWNOUT //No brownout reset |
| #FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O |
| #FUSES NOCPD //No EE protection |
| #FUSES NOWRT //Program memory not write protected |
| #use delay(clock=20000000) |
| /programy/C/PIC/test/C16F873/blik/main.hex |
|---|
| 0,0 → 1,17 |
| :1000000000308A00192800002230840000080319FB |
| :1000100016280630F800F701F70B0C28F80B0B2810 |
| :100020007B30F700F70B1228800B09288A110A127F |
| :100030006E2884011F30830583161F149F141F151B |
| :100040009F1107309C00FF308312A00083161F14FD |
| :100050009F141F159F1183121F109412A0122008C5 |
| :1000600083168700831220162008831687008312C8 |
| :10007000A011200883168700003083129400831695 |
| :1000800094000108C73908388100831290010030BC |
| :10009000F800920000308316920007309C0005089B |
| :1000A0001030F700F70B522800001C0883120D13C4 |
| :1000B00083169D018312A0102008831687008312E7 |
| :1000C00087102108A10AA2000030A0008316870132 |
| :1000D0008312220887006430A2000428612863008C |
| :02400E003A3F37 |
| :00000001FF |
| ;PIC16F876A |
| /programy/C/PIC/test/C16F876A/blik/blik.PJT |
|---|
| 0,0 → 1,38 |
| [PROJECT] |
| Target=blik.HEX |
| Development_Mode= |
| Processor=0x876A |
| ToolSuite=CCS |
| [Directories] |
| Include=C:\Program Files\PICC\devices\;C:\Program Files\PICC\dr |
| Library= |
| LinkerScript= |
| [Target Data] |
| FileList=D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.c |
| BuildTool=C-COMPILER |
| OptionString=+FM |
| AdditionalOptionString= |
| BuildRequired=1 |
| [blik.c] |
| Type=4 |
| Path= |
| FileList= |
| BuildTool= |
| OptionString= |
| AdditionalOptionString= |
| [mru-list] |
| 1=blik.c |
| [Windows] |
| 0=0000 blik.c 0 0 796 451 3 0 |
| [Opened Files] |
| 1=D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.c |
| 2= |
| [Units] |
| Count=1 |
| 1=D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.c (main) |
| /programy/C/PIC/test/C16F876A/blik/blik.cof |
|---|
| Cannot display: file marked as a binary type. |
| svn:mime-type = application/octet-stream |
| Property changes: |
| Added: svn:mime-type |
| +application/octet-stream |
| \ No newline at end of property |
| /programy/C/PIC/test/C16F876A/blik/blik.lst |
|---|
| 0,0 → 1,175 |
| CCS PCM C Compiler, Version 3.245, 27853 29-VI-08 23:25 |
| Filename: D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.lst |
| ROM used: 114 words (1%) |
| Largest free fragment is 2048 |
| RAM used: 7 (4%) at main() level |
| 8 (5%) worst case |
| Stack: 1 locations |
| * |
| 0000: MOVLW 00 |
| 0001: MOVWF 0A |
| 0002: GOTO 017 |
| 0003: NOP |
| .................... #include ".\blik.h" |
| .................... #include <16F876A.h> |
| .................... //////// Standard Header file for the PIC16F876A device //////////////// |
| .................... #device PIC16F876A |
| .................... #list |
| .................... |
| .................... #device adc=8 |
| .................... |
| .................... #FUSES NOWDT //No Watch Dog Timer |
| .................... #FUSES HS //High speed Osc (> 4mhz) |
| .................... #FUSES NOPUT //No Power Up Timer |
| .................... #FUSES NOPROTECT //Code not protected from reading |
| .................... #FUSES NODEBUG //No Debug mode for ICD |
| .................... #FUSES NOBROWNOUT //No brownout reset |
| .................... #FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O |
| .................... #FUSES NOCPD //No EE protection |
| .................... #FUSES NOWRT //Program memory not write protected |
| .................... |
| .................... #use delay(clock=20000000) |
| 0004: MOVLW 22 |
| 0005: MOVWF 04 |
| 0006: MOVF 00,W |
| 0007: BTFSC 03.2 |
| 0008: GOTO 016 |
| 0009: MOVLW 06 |
| 000A: MOVWF 78 |
| 000B: CLRF 77 |
| 000C: DECFSZ 77,F |
| 000D: GOTO 00C |
| 000E: DECFSZ 78,F |
| 000F: GOTO 00B |
| 0010: MOVLW 7B |
| 0011: MOVWF 77 |
| 0012: DECFSZ 77,F |
| 0013: GOTO 012 |
| 0014: DECFSZ 00,F |
| 0015: GOTO 009 |
| 0016: RETLW 00 |
| .................... |
| .................... |
| .................... |
| .................... |
| .................... void main() |
| .................... { |
| 0017: CLRF 04 |
| 0018: MOVLW 1F |
| 0019: ANDWF 03,F |
| 001A: BSF 03.5 |
| 001B: BSF 1F.0 |
| 001C: BSF 1F.1 |
| 001D: BSF 1F.2 |
| 001E: BCF 1F.3 |
| 001F: MOVLW 07 |
| 0020: MOVWF 1C |
| .................... |
| .................... setup_adc_ports(NO_ANALOGS); |
| * |
| 0024: BSF 03.5 |
| 0025: BSF 1F.0 |
| 0026: BSF 1F.1 |
| 0027: BSF 1F.2 |
| 0028: BCF 1F.3 |
| .................... setup_adc(ADC_OFF); |
| 0029: BCF 03.5 |
| 002A: BCF 1F.0 |
| .................... setup_spi(FALSE); |
| * |
| 0021: MOVLW FF |
| 0022: BCF 03.5 |
| 0023: MOVWF 20 |
| * |
| 002B: BCF 14.5 |
| 002C: BCF 20.5 |
| 002D: MOVF 20,W |
| 002E: BSF 03.5 |
| 002F: MOVWF 07 |
| 0030: BCF 03.5 |
| 0031: BSF 20.4 |
| 0032: MOVF 20,W |
| 0033: BSF 03.5 |
| 0034: MOVWF 07 |
| 0035: BCF 03.5 |
| 0036: BCF 20.3 |
| 0037: MOVF 20,W |
| 0038: BSF 03.5 |
| 0039: MOVWF 07 |
| 003A: MOVLW 00 |
| 003B: BCF 03.5 |
| 003C: MOVWF 14 |
| 003D: BSF 03.5 |
| 003E: MOVWF 14 |
| .................... setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
| 003F: MOVF 01,W |
| 0040: ANDLW C7 |
| 0041: IORLW 08 |
| 0042: MOVWF 01 |
| .................... setup_timer_1(T1_DISABLED); |
| 0043: BCF 03.5 |
| 0044: CLRF 10 |
| .................... setup_timer_2(T2_DISABLED,0,1); |
| 0045: MOVLW 00 |
| 0046: MOVWF 78 |
| 0047: MOVWF 12 |
| 0048: MOVLW 00 |
| 0049: BSF 03.5 |
| 004A: MOVWF 12 |
| .................... setup_comparator(NC_NC_NC_NC); |
| 004B: MOVLW 07 |
| 004C: MOVWF 1C |
| 004D: MOVF 05,W |
| 004E: MOVLW 10 |
| 004F: MOVWF 77 |
| 0050: DECFSZ 77,F |
| 0051: GOTO 050 |
| 0052: NOP |
| 0053: MOVF 1C,W |
| 0054: BCF 03.5 |
| 0055: BCF 0D.6 |
| .................... setup_vref(FALSE); |
| 0056: BSF 03.5 |
| 0057: CLRF 1D |
| .................... |
| .................... While(true) |
| .................... { |
| .................... Delay_ms(500); |
| 0058: MOVLW 02 |
| 0059: BCF 03.5 |
| 005A: MOVWF 21 |
| 005B: MOVLW FA |
| 005C: MOVWF 22 |
| 005D: CALL 004 |
| 005E: DECFSZ 21,F |
| 005F: GOTO 05B |
| .................... Output_high(PIN_B1); |
| 0060: BSF 03.5 |
| 0061: BCF 06.1 |
| 0062: BCF 03.5 |
| 0063: BSF 06.1 |
| .................... Delay_ms(500); |
| 0064: MOVLW 02 |
| 0065: MOVWF 21 |
| 0066: MOVLW FA |
| 0067: MOVWF 22 |
| 0068: CALL 004 |
| 0069: DECFSZ 21,F |
| 006A: GOTO 066 |
| .................... Output_low(PIN_B1); |
| 006B: BSF 03.5 |
| 006C: BCF 06.1 |
| 006D: BCF 03.5 |
| 006E: BCF 06.1 |
| .................... } |
| 006F: BSF 03.5 |
| 0070: GOTO 058 |
| .................... |
| .................... } |
| 0071: SLEEP |
| Configuration Fuses: |
| Word 1: 3F3A HS NOWDT NOPUT NODEBUG NOPROTECT NOBROWNOUT NOLVP NOCPD NOWRT |
| /programy/C/PIC/test/C16F876A/blik/blik.sta |
|---|
| 0,0 → 1,31 |
| ROM used: 114 (1%) |
| 114 (1%) including unused fragments |
| 0 Average locations per line |
| 8 Average locations per statement |
| RAM used: 7 (4%) at main() level |
| 8 (5%) worst case |
| Lines Stmts % Files |
| ----- ----- --- ----- |
| 25 14 100 D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.c |
| 16 0 0 D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.h |
| 270 0 0 C:\Program Files\PICC\devices\16F876A.h |
| ----- ----- |
| 622 28 Total |
| Page ROM % RAM Functions: |
| ---- --- --- --- ---------- |
| 0 19 17 1 @delay_ms1 |
| 0 91 80 1 main |
| Segment Used Free |
| --------- ---- ---- |
| 00000-00003 4 0 |
| 00004-007FF 110 1934 |
| 00800-00FFF 0 2048 |
| 01000-017FF 0 2048 |
| 01800-01FFF 0 2048 |
| /programy/C/PIC/test/C16F876A/blik/blik.sym |
|---|
| 0,0 → 1,45 |
| 015-016 CCP_1 |
| 015 CCP_1_LOW |
| 016 CCP_1_HIGH |
| 01B CCP_2_LOW |
| 01B-01C CCP_2 |
| 01C CCP_2_HIGH |
| 020 @TRIS_C |
| 021 main.@SCRATCH |
| 022 @delay_ms1.P1 |
| 077 @SCRATCH |
| 078 @SCRATCH |
| 078 _RETURN_ |
| 079 @SCRATCH |
| 07A @SCRATCH |
| 07B @SCRATCH |
| 09C.6 C1OUT |
| 09C.7 C2OUT |
| 0004 @delay_ms1 |
| 0017 main |
| 0017 @cinit |
| Project Files: |
| D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.c |
| D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.h |
| C:\Program Files\PICC\devices\16F876A.h |
| Units: |
| D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.c (main) |
| Compiler Settings: |
| Processor: PIC16F876A |
| Pointer Size: 8 |
| ADC Range: 0-255 |
| Opt Level: 9 |
| Short,Int,Long: 1,8,16 |
| Output Files: |
| Errors: D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.err |
| INHX8: D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.hex |
| Symbols: D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.sym |
| List: D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.lst |
| Debug/COFF: D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.cof |
| Call Tree: D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.tre |
| Statistics: D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.sta |
| /programy/C/PIC/test/C16F876A/blik/blik.BAK |
|---|
| 0,0 → 1,24 |
| #include "D:\KAKLIK\projekty\programy\PIC_C\test\PIC16F876A\blik\blik.h" |
| void main() |
| { |
| setup_adc_ports(NO_ANALOGS); |
| setup_adc(ADC_OFF); |
| setup_spi(FALSE); |
| setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
| setup_timer_1(T1_DISABLED); |
| setup_timer_2(T2_DISABLED,0,1); |
| setup_comparator(NC_NC_NC_NC); |
| setup_vref(FALSE); |
| While(true) |
| { |
| Delay_ms(500); |
| Output_high(PIN_B1); |
| Delay_ms(500); |
| Output_low(PIN_B1); |
| } |
| } |
| /programy/C/PIC/test/C16F876A/blik/blik.c |
|---|
| 0,0 → 1,24 |
| #include ".\blik.h" |
| void main() |
| { |
| setup_adc_ports(NO_ANALOGS); |
| setup_adc(ADC_OFF); |
| setup_spi(FALSE); |
| setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
| setup_timer_1(T1_DISABLED); |
| setup_timer_2(T2_DISABLED,0,1); |
| setup_comparator(NC_NC_NC_NC); |
| setup_vref(FALSE); |
| While(true) |
| { |
| Delay_ms(500); |
| Output_high(PIN_B1); |
| Delay_ms(500); |
| Output_low(PIN_B1); |
| } |
| } |
| /programy/C/PIC/test/C16F876A/blik/blik.err |
|---|
| 0,0 → 1,2 |
| No Errors |
| 0 Errors, 0 Warnings. |
| /programy/C/PIC/test/C16F876A/blik/blik.h |
|---|
| 0,0 → 1,15 |
| #include <16F876A.h> |
| #device adc=8 |
| #FUSES NOWDT //No Watch Dog Timer |
| #FUSES HS //High speed Osc (> 4mhz) |
| #FUSES NOPUT //No Power Up Timer |
| #FUSES NOPROTECT //Code not protected from reading |
| #FUSES NODEBUG //No Debug mode for ICD |
| #FUSES NOBROWNOUT //No brownout reset |
| #FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O |
| #FUSES NOCPD //No EE protection |
| #FUSES NOWRT //Program memory not write protected |
| #use delay(clock=20000000) |
| /programy/C/PIC/test/C16F876A/blik/blik.hex |
|---|
| 0,0 → 1,18 |
| :1000000000308A00172800002230840000080319FD |
| :1000100016280630F800F701F70B0C28F80B0B2810 |
| :100020007B30F700F70B1228800B0928003484017D |
| :100030001F30830583161F149F141F159F1107304F |
| :100040009C00FF308312A00083161F149F141F15FD |
| :100050009F1183121F109412A0122008831687008C |
| :10006000831220162008831687008312A01120080F |
| :1000700083168700003083129400831694000108D1 |
| :10008000C73908388100831290010030F8009200CF |
| :1000900000308316920007309C0005081030F700EE |
| :1000A000F70B502800001C0883120D1383169D01C6 |
| :1000B00002308312A100FA30A2000420A10B5B28B9 |
| :1000C00083168610831286140230A100FA30A20033 |
| :1000D0000420A10B662883168610831286108316CF |
| :0400E0005828630039 |
| :02400E003A3F37 |
| :00000001FF |
| ;PIC16F876A |
| /programy/C/PIC/test/C16F876A/blik/blik.tre |
|---|
| 0,0 → 1,5 |
| ÀÄblik |
| ÀÄmain 0/91 Ram=1 |
| ÃÄ??0?? |
| ÃÄ@delay_ms1 0/19 Ram=1 |
| ÀÄ@delay_ms1 0/19 Ram=1 |
| /programy/C/PIC/test/C16F876A/LCD/LCD.C |
|---|
| 0,0 → 1,311 |
| // LCD modul pro ovladani dvouradkoveho LCD modulu se standardnim Hitachi radicem |
| // (c)miho 2002,2005 |
| // |
| // Historie: |
| // |
| // 0.00 Uvodni verze se snadnou definici portu LCD displeje |
| // 0.01 Oprava portu (zapomenute stare identifikatory) |
| // 0.02 Doplnena moznost pripojeni datoveho portu LCD na libovolne porty |
| // 0.03 Doplnena procedura lcd_clr pro smazani displeje |
| // |
| // |
| // Funkce: |
| // |
| // lcd_init() inicializuje LCD displej a porty, nutno volat jako prvni |
| // |
| // lcd_putc(c) zapis snaku do lcd displeje, zpracovava nasledujici ridici znaky |
| // \f = \x0C - nova stranka - smazani displeje |
| // \n = \x0A - odradkovani (prechod na druhou radku) |
| // \b = \x08 - backspace - posunuti kurzoru o 1 pozici zpet |
| // \r = \x0D - goto home to position 1,1 |
| // \0 .. \7 - definovatelne znaky v pozicich 0 az 7 v CGRAM |
| // \20 .. \27 - alternativne zapsane znaky (oktalove) v pozicich 0 az 7 CGRAM |
| // Pozor na to, ze funkce printf konci tisk pokud narazi na \0 (konec retezce) |
| // |
| // lcd_gotoxy(x,y) presune kurzor na uvedenou adresu |
| // nekontroluje parametry |
| // |
| // lcd_cursor_on zapne kurzor |
| // lcd_cursor_off vypne kurzor |
| // |
| // lcd_clr smaze displej |
| // |
| // lcd_define_char(Index, Def) Makro, ktere definuje znaky od pozice Index obsahem definicniho |
| // retezce Def. Kazdych 8 znaku retezce Def definuje dalsi znak v CGRAM. |
| // Kapacita CGRAM je celkem 8 znaku s indexem 0 az 7. |
| // Na konci se provede lcd_gotoxy(1,1). |
| // Na konci teto knihovny je priklad pouziti definovanych znaku |
| // |
| // |
| // Definice portu: // Datovy port displeje pripojeny na 4 bity za sebou na jeden port |
| // |
| // #define LCD_RS PIN_B2 // rizeni registru LCD displeje |
| // #define LCD_E PIN_B1 // enable LCD displeje |
| // #define LCD_DATA_LSB PIN_C2 // pripojeni LSB bitu datoveho portu LCD displeje (celkem 4 bity vzestupne za sebou) |
| // |
| // |
| // Alternativni definice: // Datovy port displeje pripojeny na libovolne 4 bitove porty (vede na kod delsi asi o 25 slov) |
| // |
| // #define LCD_RS PIN_B2 // rizeni registru LCD displeje |
| // #define LCD_E PIN_B1 // enable LCD displeje |
| // #define LCD_D0 PIN_C2 // D0 - datove bity pripojene na libovolne porty |
| // #define LCD_D1 PIN_C3 // D1 |
| // #define LCD_D2 PIN_C4 // D2 |
| // #define LCD_D3 PIN_C5 // D3 |
| // Privatni sekce, cist jen v pripade, ze neco nefunguje |
| #ifdef LCD_DATA_LSB |
| // Generovane defince portu pro ucely teto knihovny aby kod generoval spravne IO operace a soucasne |
| // bylo mozne jednoduse deklarovat pripojene piny LCD displeje pri pouziti teto knihovny. Problem spociva |
| // v tom, ze se musi spravne ridit smery portu a soucasne datovy port zabira jen 4 bity ze zadaneho portu |
| // |
| #define LCD_SHIFT (LCD_DATA_LSB&7) // pocet bitu posuvu datoveho kanalu v datovem portu |
| #define LCD_PORT (LCD_DATA_LSB>>3) // adresa LCD datoveho portu |
| #define LCD_TRIS (LCD_PORT+0x80) // adresa prislusneho TRIS registru |
| #define LCD_MASK (0xF<<LCD_SHIFT) // maska platnych bitu |
| // |
| #if LCD_SHIFT>4 // kontrola mezi |
| #error LCD data port LSB bit not in range 0..4 |
| #endif |
| #endif |
| // Definice konstant pro LCD display |
| // |
| #define LCD_CURSOR_ON_ 0x0E // kurzor jako blikajici radka pod znakem |
| #define LCD_CURSOR_OFF_ 0x0C // zadny kurzor |
| #define LCD_LINE_2 0x40 // adresa 1. znaku 2. radky |
| // Definice rezimu LCD displeje |
| // |
| BYTE const LCD_INIT_STRING[4] = |
| { |
| 0x28, // intrfejs 4 bity, 2 radky, font 5x7 |
| LCD_CURSOR_OFF_, // display on, kurzor off, |
| 0x01, // clear displeje |
| 0x06 // inkrement pozice kurzoru (posun kurzoru doprava) |
| }; |
| // Odesle nibble do displeje (posle data a klikne signalem e) |
| // |
| void lcd_send_nibble( BYTE n ) |
| { |
| #ifdef LCD_DATA_LSB |
| // data jsou za sebou na 4 bitech jednoho portu |
| *LCD_PORT = (*LCD_PORT & ~LCD_MASK) | ((n << LCD_SHIFT) & LCD_MASK); // nastav datove bity portu a ostatni zachovej |
| #else |
| // data jsou na libovolnych 4 bitech libovolnych portu |
| output_bit(LCD_D0,bit_test(n,0)); |
| output_bit(LCD_D1,bit_test(n,1)); |
| output_bit(LCD_D2,bit_test(n,2)); |
| output_bit(LCD_D3,bit_test(n,3)); |
| #endif |
| output_bit(LCD_E,1); // vzestupna hrana |
| delay_us(1); // pockej alespon 450ns od e nebo alespon 195ns od dat |
| output_bit(LCD_E,0); // sestupna hrana (minimalni perioda e je 1us) |
| } |
| // Odesle bajt do registru LCD |
| // |
| // Pokud je Adr=0 .. instrukcni registr |
| // Pokud je Adr=1 .. datovy registr |
| // |
| void lcd_send_byte( BOOLEAN Adr, BYTE n ) |
| { |
| output_bit(LCD_RS,Adr); // vyber registr |
| swap(n); |
| lcd_send_nibble(n); // posli horni pulku bajtu |
| swap(n); |
| lcd_send_nibble(n); // posli spodni pulku bajtu |
| delay_us(40); // minimalni doba na provedeni prikazu |
| } |
| // Provede inicializaci LCD displeje, smaze obsah a nastavi mod displeje |
| // |
| // Tato procedura se musi volat pred pouzitim ostatnich lcd_ procedur |
| // |
| void lcd_init() |
| { |
| int i; // pocitadlo cyklu |
| delay_ms(20); // spozdeni pro provedeni startu displeje po zapnuti napajeni |
| #ifdef LCD_DATA_LSB |
| // data jsou na 4 bitech za sebou, nastav smer pro vsechny dalsi prenosy |
| *LCD_TRIS = *LCD_TRIS & ~LCD_MASK; // nuluj odpovidajici bity tris registru datoveho portu LCD |
| #endif |
| output_bit(LCD_RS,0); // nastav jako vystup a nastav klidovy stav |
| output_bit(LCD_E, 0); // nastav jako vystup a nastav klidovy stav |
| for (i=0; i<3; i++) // nastav lcd do rezimu 8 bitu sbernice |
| { |
| delay_ms(2); // muze byt rozdelany prenos dat (2x 4 bity) nebo pomaly povel |
| lcd_send_nibble(3); // rezim 8 bitu |
| } |
| delay_us(40); // cas na zpracovani |
| lcd_send_nibble(2); // nastav rezim 4 bitu (plati od nasledujiciho prenosu) |
| delay_us(40); // cas na zpracovani |
| for (i=0;i<3;i++) // proved inicializaci (nastaveni modu, smazani apod) |
| { |
| lcd_send_byte(0,LCD_INIT_STRING[i]); |
| delay_ms(2); |
| } |
| } |
| // Proved presun kurzoru |
| // |
| // Pozice 1.1 je domu |
| // |
| void lcd_gotoxy( BYTE x, BYTE y) |
| { |
| BYTE Adr; |
| Adr=x-1; |
| if(y==2) |
| Adr+=LCD_LINE_2; |
| lcd_send_byte(0,0x80|Adr); |
| } |
| // Zapis znaku na displej, zpracovani ridicich znaku |
| // |
| void lcd_putc( char c) |
| { |
| switch (c) |
| { |
| case '\f' : lcd_send_byte(0,1); // smaz displej |
| delay_ms(2); |
| break; |
| case '\n' : lcd_gotoxy(1,2); break; // presun se na 1. znak 2. radky |
| case '\r' : lcd_gotoxy(1,1); break; // presun home |
| case '\b' : lcd_send_byte(0,0x10); break; // posun kurzor o 1 zpet |
| default : if (c<0x20) c&=0x7; // preklopeni definovatelnych znaku na rozsah 0 az 0x1F |
| lcd_send_byte(1,c); break; // zapis znak |
| } |
| } |
| // Zapni kurzor |
| // |
| void lcd_cursor_on() |
| { |
| lcd_send_byte(0,LCD_CURSOR_ON_); |
| } |
| // Vypni kurzor |
| // |
| void lcd_cursor_off() |
| { |
| lcd_send_byte(0,LCD_CURSOR_OFF_); |
| } |
| // Smaz displej |
| // |
| void lcd_clr() |
| { |
| lcd_putc('\f'); |
| } |
| // Definice vlastnich fontu |
| // |
| // Vlastnich definic muze byt jen 8 do pozic 0 az 7 pameti CGRAM radice lcd displeje |
| // Pro snadne definovani jsou pripraveny nasledujici definice a na konci souboru je uveden |
| // priklad pouziti definovanych znaku. |
| // Pomocna procedura pro posilani ridicich dat do radice displeje |
| // |
| void lcd_putc2(int Data) |
| { |
| lcd_send_byte(1,Data); |
| } |
| // Pomocne definice pro programovani obsahu CGRAM |
| // |
| #define lcd_define_start(Code) lcd_send_byte(0,0x40+(Code<<3)); delay_ms(2) |
| #define lcd_define_def(String) printf(lcd_putc2,String); |
| #define lcd_define_end() lcd_send_byte(0,3); delay_ms(2) |
| // Vlastni vykonne makro pro definovani fontu do pozice Index CGRAM s definicnim retezcem Def |
| // |
| #define lcd_define_char(Index, Def) lcd_define_start(Index); lcd_define_def(Def); lcd_define_end(); |
| // Pripravene definice fontu vybranych znaku |
| // V tabulce nesmi byt 00 (konec retezce v printf()), misto toho davame 80 |
| // |
| #define LCD_CHAR_BAT100 "\x0E\x1F\x1F\x1F\x1F\x1F\x1F\x1F" /* symbol plne baterie */ |
| #define LCD_CHAR_BAT50 "\x0E\x1F\x11\x11\x13\x17\x1F\x1F" /* symbol polovicni baterie */ |
| #define LCD_CHAR_BAT0 "\x0E\x1F\x11\x11\x11\x11\x11\x1F" /* symbol vybite baterie */ |
| #define LCD_CHAR_UP "\x80\x04\x0E\x15\x04\x04\x04\x80" /* symbol sipka nahoru */ |
| #define LCD_CHAR_DOWN "\x80\x04\x04\x04\x15\x0E\x04\x80" /* symbol Sipka dolu */ |
| #define LCD_CHAR_LUA "\x04\x0E\x11\x11\x1F\x11\x11\x80" /* A s carkou */ |
| #define LCD_CHAR_LLA "\x01\x02\x0E\x01\x1F\x11\x0F\x80" /* a s carkou */ |
| #define LCD_CHAR_HUC "\x0A\x0E\x11\x10\x10\x11\x0E\x80" /* C s hackem */ |
| #define LCD_CHAR_HLC "\x0A\x04\x0E\x10\x10\x11\x0E\x80" /* c s hackem */ |
| #define LCD_CHAR_HUD "\x0A\x1C\x12\x11\x11\x12\x1C\x80" /* D s hackem */ |
| #define LCD_CHAR_HLD "\x05\x03\x0D\x13\x11\x11\x0F\x80" /* d s hackem */ |
| #define LCD_CHAR_LUE "\x04\x1F\x10\x10\x1E\x10\x1F\x80" /* E s carkou */ |
| #define LCD_CHAR_LLE "\x01\x02\x0E\x11\x1F\x10\x0E\x80" /* e s carkou */ |
| #define LCD_CHAR_HUE "\x0A\x1F\x10\x1E\x10\x10\x1F\x80" /* E s hackem */ |
| #define LCD_CHAR_HLE "\x0A\x04\x0E\x11\x1F\x10\x0E\x80" /* e s hackem */ |
| #define LCD_CHAR_LUI "\x04\x0E\x04\x04\x04\x04\x0E\x80" /* I s carkou */ |
| #define LCD_CHAR_LLI "\x02\x04\x80\x0C\x04\x04\x0E\x80" /* i s carkou */ |
| #define LCD_CHAR_HUN "\x0A\x15\x11\x19\x15\x13\x11\x80" /* N s hackem */ |
| #define LCD_CHAR_HLN "\x0A\x04\x16\x19\x11\x11\x11\x80" /* n s hackem */ |
| #define LCD_CHAR_LUO "\x04\x0E\x11\x11\x11\x11\x0E\x80" /* O s carkou */ |
| #define LCD_CHAR_LLO "\x02\x04\x0E\x11\x11\x11\x0E\x80" /* o s carkou */ |
| #define LCD_CHAR_HUR "\x0A\x1E\x11\x1E\x14\x12\x11\x80" /* R s hackem */ |
| #define LCD_CHAR_HLR "\x0A\x04\x16\x19\x10\x10\x10\x80" /* r s hackem */ |
| #define LCD_CHAR_HUS "\x0A\x0F\x10\x0E\x01\x01\x1E\x80" /* S s hackem */ |
| #define LCD_CHAR_HLS "\x0A\x04\x0E\x10\x0E\x01\x1E\x80" /* s s hackem */ |
| #define LCD_CHAR_HUT "\x0A\x1F\x04\x04\x04\x04\x04\x80" /* T s hackem */ |
| #define LCD_CHAR_HLT "\x0A\x0C\x1C\x08\x08\x09\x06\x80" /* t s hackem */ |
| #define LCD_CHAR_LUU "\x02\x15\x11\x11\x11\x11\x0E\x80" /* U s carkou */ |
| #define LCD_CHAR_LLU "\x02\x04\x11\x11\x11\x13\x0D\x80" /* u s carkou */ |
| #define LCD_CHAR_CUU "\x06\x17\x11\x11\x11\x11\x0E\x80" /* U s krouzkem */ |
| #define LCD_CHAR_CLU "\x06\x06\x11\x11\x11\x11\x0E\x80" /* u s krouzkem */ |
| #define LCD_CHAR_LUY "\x02\x15\x11\x0A\x04\x04\x04\x80" /* Y s carkou */ |
| #define LCD_CHAR_LLY "\x02\x04\x11\x11\x0F\x01\x0E\x80" /* y s carkou */ |
| #define LCD_CHAR_HUZ "\x0A\x1F\x01\x02\x04\x08\x1F\x80" /* Z s hackem */ |
| #define LCD_CHAR_HLZ "\x0A\x04\x1F\x02\x04\x08\x1F\x80" /* z s hackem */ |
| // Priklad pouziti definovanych znaku |
| // |
| // |
| //void lcd_sample() |
| //{ |
| // lcd_define_char(0,LCD_CHAR_BAT50); // Priklad definice znaku baterie do pozice 0 |
| // lcd_define_char(2,LCD_CHAR_HLE LCD_CHAR_LUI); // Priklad definice znaku e s hackem a I s carkou od pozice 2 |
| // // vsimnete si, ze neni carka mezi retezci s definici (oba retezce definuji |
| // // jediny definicni retezec) |
| // printf(lcd_putc,"\fZnaky:\20\22\23"); // priklad vypisu znaku z pozice 0, 2 a 3 |
| // delay_ms(1000); |
| // lcd_define_char(0,LCD_CHAR_BAT0); // Predefinovani tvaru znaku v pozici 0 |
| // delay_ms(1000); |
| //} |
| Property changes: |
| Added: svn:executable |
| +* |
| \ No newline at end of property |
| /programy/C/PIC/test/C16F876A/LCD/main.BAK |
|---|
| 0,0 → 1,31 |
| #include "main.h" |
| #define LCD_RS PIN_B1 // rizeni registru LCD displeje |
| #define LCD_E PIN_B0 // enable LCD displeje |
| #define LCD_DATA_LSB PIN_C4 // pripojeni LSB bitu datoveho portu LCD displeje (celkem 4 bity vzestupne za sebou) |
| #include "LCD.C" |
| void main() |
| { |
| setup_adc_ports(NO_ANALOGS); |
| setup_adc(ADC_OFF); |
| setup_psp(PSP_DISABLED); |
| setup_spi(FALSE); |
| setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
| setup_timer_1(T1_DISABLED); |
| setup_timer_2(T2_DISABLED,0,1); |
| lcd_init(); |
| while(true); |
| { |
| Delay_ms(100); |
| LCD_gotoxy(1,1); |
| printf(lcd_putc,"Ahoj, Display funguje"); |
| } |
| } |
| /programy/C/PIC/test/C16F876A/LCD/main.PJT |
|---|
| 0,0 → 1,39 |
| [PROJECT] |
| Target=main.HEX |
| Development_Mode= |
| Processor=0x877F |
| ToolSuite=CCS |
| [Directories] |
| Library= |
| LinkerScript= |
| [Target Data] |
| FileList=C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\main.c |
| BuildTool=C-COMPILER |
| OptionString=+FM |
| AdditionalOptionString= |
| BuildRequired=1 |
| [main.] |
| Type=4 |
| Path= |
| FileList= |
| BuildTool= |
| OptionString= |
| AdditionalOptionString= |
| [mru-list] |
| 1=main. |
| [Windows] |
| 0=0000 main. 0 0 796 451 3 0 |
| [Opened Files] |
| 1=C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\main.c |
| 2= |
| [Units] |
| Count=1 |
| 1=C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\main.c (main) |
| /programy/C/PIC/test/C16F876A/LCD/main.c |
|---|
| 0,0 → 1,34 |
| #include "main.h" |
| #define LCD_RS PIN_C7 // rizeni registru LCD displeje <lcd.c> |
| #define LCD_E PIN_B7 // enable LCD displeje <lcd.c> |
| #define LCD_D0 PIN_B3 // data LCD <lcd.c> |
| #define LCD_D1 PIN_B2 |
| #define LCD_D2 PIN_B1 |
| #define LCD_D3 PIN_B0 |
| #include "LCD.C" |
| void main() |
| { |
| setup_adc_ports(NO_ANALOGS); |
| setup_adc(ADC_OFF); |
| setup_psp(PSP_DISABLED); |
| setup_spi(FALSE); |
| setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
| setup_timer_1(T1_DISABLED); |
| setup_timer_2(T2_DISABLED,0,1); |
| lcd_init(); |
| while(true); |
| { |
| Delay_ms(100); |
| LCD_gotoxy(1,1); |
| printf(lcd_putc,"Ahoj, Display funguje"); |
| } |
| } |
| /programy/C/PIC/test/C16F876A/LCD/main.cof |
|---|
| Cannot display: file marked as a binary type. |
| svn:mime-type = application/octet-stream |
| Property changes: |
| Added: svn:mime-type |
| +application/octet-stream |
| \ No newline at end of property |
| /programy/C/PIC/test/C16F876A/LCD/main.err |
|---|
| 0,0 → 1,2 |
| No Errors |
| 0 Errors, 0 Warnings. |
| /programy/C/PIC/test/C16F876A/LCD/main.h |
|---|
| 0,0 → 1,15 |
| #include <16F877.h> |
| #device adc=8 |
| #FUSES NOWDT //No Watch Dog Timer |
| #FUSES XT //Crystal osc <= 4mhz |
| #FUSES NOPUT //No Power Up Timer |
| #FUSES NOPROTECT //Code not protected from reading |
| #FUSES NOBROWNOUT //No brownout reset |
| #FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O |
| #FUSES NOCPD //No EE protection |
| #FUSES NOWRT //Program memory not write protected |
| #FUSES NODEBUG //No Debug mode for ICD |
| #use delay(clock=4000000) |
| /programy/C/PIC/test/C16F876A/LCD/main.hex |
|---|
| 0,0 → 1,44 |
| :1000000000308A00FC2800000A108A100A118207BA |
| :1000100028340C34013406340A108A100A1182077D |
| :10002000413468346F346A342C34203444346934B5 |
| :10003000733470346C3461347934203466347534FC |
| :100040006E34673475346A34653400342330840088 |
| :10005000000803193A280130F800F701F70B2E28A1 |
| :10006000F80B2D284A30F700F70B34280000000069 |
| :10007000800B2B28003429183F288611402886152C |
| :10008000831686118312A9184728061148280615D9 |
| :1000900083160611831229194F28861050288614BA |
| :1000A000831686108312A91957280610582806149B |
| :1000B0008316061083128617831686130000831298 |
| :1000C00086138316861383120034A708031D6A283B |
| :1000D00087136B288717A0132008831687008312C5 |
| :1000E000A80E2808A9003B20A80E2808A9003B203C |
| :1000F0000D30F700F70B7A2800341430A3002620C7 |
| :100100008713A01320088316870083128613831693 |
| :1001100086138312A1012108023C031C9728023098 |
| :10012000A30026200330A9003B20A10A8B280D3014 |
| :10013000F700F70B99280230A9003B200D30F7009B |
| :10014000F70BA028A1012108023C031CB3282108B9 |
| :100150000420A200A7012208A80065200230A30005 |
| :100160002620A10AA3288A110A123329013023026A |
| :10017000A5002408023C031DBF284030A507250820 |
| :100180008038A600A7012608A800652000342208B0 |
| :100190000C3A0319D528063A0319DD28073A031942 |
| :1001A000E328053A0319E828ED28A7010130A80043 |
| :1001B00065200230A3002620F9280130A300023078 |
| :1001C000A400B620F9280130A300A400B620F92825 |
| :1001D000A7011030A8006520F92822081F3C031C45 |
| :1001E000F3280730A2050130A7002208A8006520E7 |
| :1001F000F9288A110A12442984011F3083058316C5 |
| :100200001F149F141F159F11FF308312A000831627 |
| :100210001F149F141F159F1183121F10831609129C |
| :1002200083129412A01220088316870083122016CE |
| :100230002008831687008312A011200883168700E8 |
| :10024000003083129400831694000108C7390838DF |
| :100250008100831290010030F80092000030831674 |
| :10026000920083127D2833296430A30026200130B8 |
| :10027000A300A400B620A10121080C200038031916 |
| :0C0280004529A10AA200C7283C29630000 |
| :02400E00393F38 |
| :00000001FF |
| ;PIC16F877 |
| /programy/C/PIC/test/C16F876A/LCD/main.lst |
|---|
| 0,0 → 1,675 |
| CCS PCM C Compiler, Version 3.245, 27853 16-XII-07 14:06 |
| Filename: C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\main.lst |
| ROM used: 326 words (4%) |
| Largest free fragment is 2048 |
| RAM used: 7 (4%) at main() level |
| 15 (9%) worst case |
| Stack: 4 locations |
| * |
| 0000: MOVLW 00 |
| 0001: MOVWF 0A |
| 0002: GOTO 0FC |
| 0003: NOP |
| .................... #include "main.h" |
| .................... #include <16F877.h> |
| .................... //////// Standard Header file for the PIC16F877 device //////////////// |
| .................... #device PIC16F877 |
| .................... #list |
| .................... |
| .................... #device adc=8 |
| .................... |
| .................... #FUSES NOWDT //No Watch Dog Timer |
| .................... #FUSES XT //Crystal osc <= 4mhz |
| .................... #FUSES NOPUT //No Power Up Timer |
| .................... #FUSES NOPROTECT //Code not protected from reading |
| .................... #FUSES NOBROWNOUT //No brownout reset |
| .................... #FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O |
| .................... #FUSES NOCPD //No EE protection |
| .................... #FUSES NOWRT //Program memory not write protected |
| .................... #FUSES NODEBUG //No Debug mode for ICD |
| .................... |
| .................... #use delay(clock=4000000) |
| 0026: MOVLW 23 |
| 0027: MOVWF 04 |
| 0028: MOVF 00,W |
| 0029: BTFSC 03.2 |
| 002A: GOTO 03A |
| 002B: MOVLW 01 |
| 002C: MOVWF 78 |
| 002D: CLRF 77 |
| 002E: DECFSZ 77,F |
| 002F: GOTO 02E |
| 0030: DECFSZ 78,F |
| 0031: GOTO 02D |
| 0032: MOVLW 4A |
| 0033: MOVWF 77 |
| 0034: DECFSZ 77,F |
| 0035: GOTO 034 |
| 0036: NOP |
| 0037: NOP |
| 0038: DECFSZ 00,F |
| 0039: GOTO 02B |
| 003A: RETLW 00 |
| .................... |
| .................... |
| .................... |
| .................... |
| .................... #define LCD_RS PIN_C7 // rizeni registru LCD displeje <lcd.c> |
| .................... #define LCD_E PIN_B7 // enable LCD displeje <lcd.c> |
| .................... #define LCD_D0 PIN_B3 // data LCD <lcd.c> |
| .................... #define LCD_D1 PIN_B2 |
| .................... #define LCD_D2 PIN_B1 |
| .................... #define LCD_D3 PIN_B0 |
| .................... |
| .................... #include "LCD.C" |
| .................... // LCD modul pro ovladani dvouradkoveho LCD modulu se standardnim Hitachi radicem |
| .................... // (c)miho 2002,2005 |
| .................... // |
| .................... // Historie: |
| .................... // |
| .................... // 0.00 Uvodni verze se snadnou definici portu LCD displeje |
| .................... // 0.01 Oprava portu (zapomenute stare identifikatory) |
| .................... // 0.02 Doplnena moznost pripojeni datoveho portu LCD na libovolne porty |
| .................... // 0.03 Doplnena procedura lcd_clr pro smazani displeje |
| .................... // |
| .................... // |
| .................... // Funkce: |
| .................... // |
| .................... // lcd_init() inicializuje LCD displej a porty, nutno volat jako prvni |
| .................... // |
| .................... // lcd_putc(c) zapis snaku do lcd displeje, zpracovava nasledujici ridici znaky |
| .................... // \f = \x0C - nova stranka - smazani displeje |
| .................... // \n = \x0A - odradkovani (prechod na druhou radku) |
| .................... // \b = \x08 - backspace - posunuti kurzoru o 1 pozici zpet |
| .................... // \r = \x0D - goto home to position 1,1 |
| .................... // \0 .. \7 - definovatelne znaky v pozicich 0 az 7 v CGRAM |
| .................... // \20 .. \27 - alternativne zapsane znaky (oktalove) v pozicich 0 az 7 CGRAM |
| .................... // Pozor na to, ze funkce printf konci tisk pokud narazi na \0 (konec retezce) |
| .................... // |
| .................... // lcd_gotoxy(x,y) presune kurzor na uvedenou adresu |
| .................... // nekontroluje parametry |
| .................... // |
| .................... // lcd_cursor_on zapne kurzor |
| .................... // lcd_cursor_off vypne kurzor |
| .................... // |
| .................... // lcd_clr smaze displej |
| .................... // |
| .................... // lcd_define_char(Index, Def) Makro, ktere definuje znaky od pozice Index obsahem definicniho |
| .................... // retezce Def. Kazdych 8 znaku retezce Def definuje dalsi znak v CGRAM. |
| .................... // Kapacita CGRAM je celkem 8 znaku s indexem 0 az 7. |
| .................... // Na konci se provede lcd_gotoxy(1,1). |
| .................... // Na konci teto knihovny je priklad pouziti definovanych znaku |
| .................... // |
| .................... // |
| .................... // Definice portu: // Datovy port displeje pripojeny na 4 bity za sebou na jeden port |
| .................... // |
| .................... // #define LCD_RS PIN_B2 // rizeni registru LCD displeje |
| .................... // #define LCD_E PIN_B1 // enable LCD displeje |
| .................... // #define LCD_DATA_LSB PIN_C2 // pripojeni LSB bitu datoveho portu LCD displeje (celkem 4 bity vzestupne za sebou) |
| .................... // |
| .................... // |
| .................... // Alternativni definice: // Datovy port displeje pripojeny na libovolne 4 bitove porty (vede na kod delsi asi o 25 slov) |
| .................... // |
| .................... // #define LCD_RS PIN_B2 // rizeni registru LCD displeje |
| .................... // #define LCD_E PIN_B1 // enable LCD displeje |
| .................... // #define LCD_D0 PIN_C2 // D0 - datove bity pripojene na libovolne porty |
| .................... // #define LCD_D1 PIN_C3 // D1 |
| .................... // #define LCD_D2 PIN_C4 // D2 |
| .................... // #define LCD_D3 PIN_C5 // D3 |
| .................... |
| .................... |
| .................... |
| .................... |
| .................... // Privatni sekce, cist jen v pripade, ze neco nefunguje |
| .................... |
| .................... |
| .................... |
| .................... |
| .................... #ifdef LCD_DATA_LSB |
| .................... // Generovane defince portu pro ucely teto knihovny aby kod generoval spravne IO operace a soucasne |
| .................... // bylo mozne jednoduse deklarovat pripojene piny LCD displeje pri pouziti teto knihovny. Problem spociva |
| .................... // v tom, ze se musi spravne ridit smery portu a soucasne datovy port zabira jen 4 bity ze zadaneho portu |
| .................... // |
| .................... #define LCD_SHIFT (LCD_DATA_LSB&7) // pocet bitu posuvu datoveho kanalu v datovem portu |
| .................... #define LCD_PORT (LCD_DATA_LSB>>3) // adresa LCD datoveho portu |
| .................... #define LCD_TRIS (LCD_PORT+0x80) // adresa prislusneho TRIS registru |
| .................... #define LCD_MASK (0xF<<LCD_SHIFT) // maska platnych bitu |
| .................... // |
| .................... #if LCD_SHIFT>4 // kontrola mezi |
| .................... #error LCD data port LSB bit not in range 0..4 |
| .................... #endif |
| .................... #endif |
| .................... |
| .................... |
| .................... // Definice konstant pro LCD display |
| .................... // |
| .................... #define LCD_CURSOR_ON_ 0x0E // kurzor jako blikajici radka pod znakem |
| .................... #define LCD_CURSOR_OFF_ 0x0C // zadny kurzor |
| .................... #define LCD_LINE_2 0x40 // adresa 1. znaku 2. radky |
| .................... |
| .................... |
| .................... // Definice rezimu LCD displeje |
| .................... // |
| .................... BYTE const LCD_INIT_STRING[4] = |
| .................... { |
| .................... 0x28, // intrfejs 4 bity, 2 radky, font 5x7 |
| .................... LCD_CURSOR_OFF_, // display on, kurzor off, |
| .................... 0x01, // clear displeje |
| .................... 0x06 // inkrement pozice kurzoru (posun kurzoru doprava) |
| .................... }; |
| .................... |
| .................... |
| .................... // Odesle nibble do displeje (posle data a klikne signalem e) |
| .................... // |
| .................... void lcd_send_nibble( BYTE n ) |
| .................... { |
| .................... #ifdef LCD_DATA_LSB |
| .................... // data jsou za sebou na 4 bitech jednoho portu |
| .................... *LCD_PORT = (*LCD_PORT & ~LCD_MASK) | ((n << LCD_SHIFT) & LCD_MASK); // nastav datove bity portu a ostatni zachovej |
| .................... #else |
| .................... // data jsou na libovolnych 4 bitech libovolnych portu |
| .................... output_bit(LCD_D0,bit_test(n,0)); |
| 003B: BTFSC 29.0 |
| 003C: GOTO 03F |
| 003D: BCF 06.3 |
| 003E: GOTO 040 |
| 003F: BSF 06.3 |
| 0040: BSF 03.5 |
| 0041: BCF 06.3 |
| .................... output_bit(LCD_D1,bit_test(n,1)); |
| 0042: BCF 03.5 |
| 0043: BTFSC 29.1 |
| 0044: GOTO 047 |
| 0045: BCF 06.2 |
| 0046: GOTO 048 |
| 0047: BSF 06.2 |
| 0048: BSF 03.5 |
| 0049: BCF 06.2 |
| .................... output_bit(LCD_D2,bit_test(n,2)); |
| 004A: BCF 03.5 |
| 004B: BTFSC 29.2 |
| 004C: GOTO 04F |
| 004D: BCF 06.1 |
| 004E: GOTO 050 |
| 004F: BSF 06.1 |
| 0050: BSF 03.5 |
| 0051: BCF 06.1 |
| .................... output_bit(LCD_D3,bit_test(n,3)); |
| 0052: BCF 03.5 |
| 0053: BTFSC 29.3 |
| 0054: GOTO 057 |
| 0055: BCF 06.0 |
| 0056: GOTO 058 |
| 0057: BSF 06.0 |
| 0058: BSF 03.5 |
| 0059: BCF 06.0 |
| .................... #endif |
| .................... output_bit(LCD_E,1); // vzestupna hrana |
| 005A: BCF 03.5 |
| 005B: BSF 06.7 |
| 005C: BSF 03.5 |
| 005D: BCF 06.7 |
| .................... delay_us(1); // pockej alespon 450ns od e nebo alespon 195ns od dat |
| 005E: NOP |
| .................... output_bit(LCD_E,0); // sestupna hrana (minimalni perioda e je 1us) |
| 005F: BCF 03.5 |
| 0060: BCF 06.7 |
| 0061: BSF 03.5 |
| 0062: BCF 06.7 |
| .................... } |
| 0063: BCF 03.5 |
| 0064: RETLW 00 |
| .................... |
| .................... |
| .................... // Odesle bajt do registru LCD |
| .................... // |
| .................... // Pokud je Adr=0 .. instrukcni registr |
| .................... // Pokud je Adr=1 .. datovy registr |
| .................... // |
| .................... void lcd_send_byte( BOOLEAN Adr, BYTE n ) |
| .................... { |
| .................... output_bit(LCD_RS,Adr); // vyber registr |
| 0065: MOVF 27,F |
| 0066: BTFSS 03.2 |
| 0067: GOTO 06A |
| 0068: BCF 07.7 |
| 0069: GOTO 06B |
| 006A: BSF 07.7 |
| 006B: BCF 20.7 |
| 006C: MOVF 20,W |
| 006D: BSF 03.5 |
| 006E: MOVWF 07 |
| * |
| 0104: MOVLW FF |
| 0105: BCF 03.5 |
| 0106: MOVWF 20 |
| .................... swap(n); |
| * |
| 006F: BCF 03.5 |
| 0070: SWAPF 28,F |
| .................... lcd_send_nibble(n); // posli horni pulku bajtu |
| 0071: MOVF 28,W |
| 0072: MOVWF 29 |
| 0073: CALL 03B |
| .................... swap(n); |
| 0074: SWAPF 28,F |
| .................... lcd_send_nibble(n); // posli spodni pulku bajtu |
| 0075: MOVF 28,W |
| 0076: MOVWF 29 |
| 0077: CALL 03B |
| .................... delay_us(40); // minimalni doba na provedeni prikazu |
| 0078: MOVLW 0D |
| 0079: MOVWF 77 |
| 007A: DECFSZ 77,F |
| 007B: GOTO 07A |
| .................... } |
| 007C: RETLW 00 |
| .................... |
| .................... |
| .................... // Provede inicializaci LCD displeje, smaze obsah a nastavi mod displeje |
| .................... // |
| .................... // Tato procedura se musi volat pred pouzitim ostatnich lcd_ procedur |
| .................... // |
| .................... void lcd_init() |
| .................... { |
| .................... |
| .................... int i; // pocitadlo cyklu |
| .................... |
| .................... delay_ms(20); // spozdeni pro provedeni startu displeje po zapnuti napajeni |
| 007D: MOVLW 14 |
| 007E: MOVWF 23 |
| 007F: CALL 026 |
| .................... |
| .................... #ifdef LCD_DATA_LSB |
| .................... // data jsou na 4 bitech za sebou, nastav smer pro vsechny dalsi prenosy |
| .................... *LCD_TRIS = *LCD_TRIS & ~LCD_MASK; // nuluj odpovidajici bity tris registru datoveho portu LCD |
| .................... #endif |
| .................... |
| .................... output_bit(LCD_RS,0); // nastav jako vystup a nastav klidovy stav |
| 0080: BCF 07.7 |
| 0081: BCF 20.7 |
| 0082: MOVF 20,W |
| 0083: BSF 03.5 |
| 0084: MOVWF 07 |
| .................... output_bit(LCD_E, 0); // nastav jako vystup a nastav klidovy stav |
| 0085: BCF 03.5 |
| 0086: BCF 06.7 |
| 0087: BSF 03.5 |
| 0088: BCF 06.7 |
| .................... |
| .................... for (i=0; i<3; i++) // nastav lcd do rezimu 8 bitu sbernice |
| 0089: BCF 03.5 |
| 008A: CLRF 21 |
| 008B: MOVF 21,W |
| 008C: SUBLW 02 |
| 008D: BTFSS 03.0 |
| 008E: GOTO 097 |
| .................... { |
| .................... delay_ms(2); // muze byt rozdelany prenos dat (2x 4 bity) nebo pomaly povel |
| 008F: MOVLW 02 |
| 0090: MOVWF 23 |
| 0091: CALL 026 |
| .................... lcd_send_nibble(3); // rezim 8 bitu |
| 0092: MOVLW 03 |
| 0093: MOVWF 29 |
| 0094: CALL 03B |
| .................... } |
| 0095: INCF 21,F |
| 0096: GOTO 08B |
| .................... |
| .................... delay_us(40); // cas na zpracovani |
| 0097: MOVLW 0D |
| 0098: MOVWF 77 |
| 0099: DECFSZ 77,F |
| 009A: GOTO 099 |
| .................... lcd_send_nibble(2); // nastav rezim 4 bitu (plati od nasledujiciho prenosu) |
| 009B: MOVLW 02 |
| 009C: MOVWF 29 |
| 009D: CALL 03B |
| .................... delay_us(40); // cas na zpracovani |
| 009E: MOVLW 0D |
| 009F: MOVWF 77 |
| 00A0: DECFSZ 77,F |
| 00A1: GOTO 0A0 |
| .................... |
| .................... for (i=0;i<3;i++) // proved inicializaci (nastaveni modu, smazani apod) |
| 00A2: CLRF 21 |
| 00A3: MOVF 21,W |
| 00A4: SUBLW 02 |
| 00A5: BTFSS 03.0 |
| 00A6: GOTO 0B3 |
| .................... { |
| .................... lcd_send_byte(0,LCD_INIT_STRING[i]); |
| 00A7: MOVF 21,W |
| 00A8: CALL 004 |
| 00A9: MOVWF 22 |
| 00AA: CLRF 27 |
| 00AB: MOVF 22,W |
| 00AC: MOVWF 28 |
| 00AD: CALL 065 |
| .................... delay_ms(2); |
| 00AE: MOVLW 02 |
| 00AF: MOVWF 23 |
| 00B0: CALL 026 |
| .................... } |
| 00B1: INCF 21,F |
| 00B2: GOTO 0A3 |
| .................... } |
| 00B3: BCF 0A.3 |
| 00B4: BCF 0A.4 |
| 00B5: GOTO 133 (RETURN) |
| .................... |
| .................... |
| .................... // Proved presun kurzoru |
| .................... // |
| .................... // Pozice 1.1 je domu |
| .................... // |
| .................... void lcd_gotoxy( BYTE x, BYTE y) |
| .................... { |
| .................... |
| .................... BYTE Adr; |
| .................... |
| .................... Adr=x-1; |
| 00B6: MOVLW 01 |
| 00B7: SUBWF 23,W |
| 00B8: MOVWF 25 |
| .................... if(y==2) |
| 00B9: MOVF 24,W |
| 00BA: SUBLW 02 |
| 00BB: BTFSS 03.2 |
| 00BC: GOTO 0BF |
| .................... Adr+=LCD_LINE_2; |
| 00BD: MOVLW 40 |
| 00BE: ADDWF 25,F |
| .................... |
| .................... lcd_send_byte(0,0x80|Adr); |
| 00BF: MOVF 25,W |
| 00C0: IORLW 80 |
| 00C1: MOVWF 26 |
| 00C2: CLRF 27 |
| 00C3: MOVF 26,W |
| 00C4: MOVWF 28 |
| 00C5: CALL 065 |
| .................... } |
| 00C6: RETLW 00 |
| .................... |
| .................... |
| .................... // Zapis znaku na displej, zpracovani ridicich znaku |
| .................... // |
| .................... void lcd_putc( char c) |
| .................... { |
| .................... |
| .................... switch (c) |
| .................... { |
| 00C7: MOVF 22,W |
| 00C8: XORLW 0C |
| 00C9: BTFSC 03.2 |
| 00CA: GOTO 0D5 |
| 00CB: XORLW 06 |
| 00CC: BTFSC 03.2 |
| 00CD: GOTO 0DD |
| 00CE: XORLW 07 |
| 00CF: BTFSC 03.2 |
| 00D0: GOTO 0E3 |
| 00D1: XORLW 05 |
| 00D2: BTFSC 03.2 |
| 00D3: GOTO 0E8 |
| 00D4: GOTO 0ED |
| .................... case '\f' : lcd_send_byte(0,1); // smaz displej |
| 00D5: CLRF 27 |
| 00D6: MOVLW 01 |
| 00D7: MOVWF 28 |
| 00D8: CALL 065 |
| .................... delay_ms(2); |
| 00D9: MOVLW 02 |
| 00DA: MOVWF 23 |
| 00DB: CALL 026 |
| .................... break; |
| 00DC: GOTO 0F9 |
| .................... case '\n' : lcd_gotoxy(1,2); break; // presun se na 1. znak 2. radky |
| 00DD: MOVLW 01 |
| 00DE: MOVWF 23 |
| 00DF: MOVLW 02 |
| 00E0: MOVWF 24 |
| 00E1: CALL 0B6 |
| 00E2: GOTO 0F9 |
| .................... case '\r' : lcd_gotoxy(1,1); break; // presun home |
| 00E3: MOVLW 01 |
| 00E4: MOVWF 23 |
| 00E5: MOVWF 24 |
| 00E6: CALL 0B6 |
| 00E7: GOTO 0F9 |
| .................... case '\b' : lcd_send_byte(0,0x10); break; // posun kurzor o 1 zpet |
| 00E8: CLRF 27 |
| 00E9: MOVLW 10 |
| 00EA: MOVWF 28 |
| 00EB: CALL 065 |
| 00EC: GOTO 0F9 |
| .................... default : if (c<0x20) c&=0x7; // preklopeni definovatelnych znaku na rozsah 0 az 0x1F |
| 00ED: MOVF 22,W |
| 00EE: SUBLW 1F |
| 00EF: BTFSS 03.0 |
| 00F0: GOTO 0F3 |
| 00F1: MOVLW 07 |
| 00F2: ANDWF 22,F |
| .................... lcd_send_byte(1,c); break; // zapis znak |
| 00F3: MOVLW 01 |
| 00F4: MOVWF 27 |
| 00F5: MOVF 22,W |
| 00F6: MOVWF 28 |
| 00F7: CALL 065 |
| 00F8: GOTO 0F9 |
| .................... } |
| .................... } |
| 00F9: BCF 0A.3 |
| 00FA: BCF 0A.4 |
| 00FB: GOTO 144 (RETURN) |
| .................... |
| .................... |
| .................... // Zapni kurzor |
| .................... // |
| .................... void lcd_cursor_on() |
| .................... { |
| .................... lcd_send_byte(0,LCD_CURSOR_ON_); |
| .................... } |
| .................... |
| .................... |
| .................... // Vypni kurzor |
| .................... // |
| .................... void lcd_cursor_off() |
| .................... { |
| .................... lcd_send_byte(0,LCD_CURSOR_OFF_); |
| .................... } |
| .................... |
| .................... |
| .................... // Smaz displej |
| .................... // |
| .................... void lcd_clr() |
| .................... { |
| .................... lcd_putc('\f'); |
| .................... } |
| .................... |
| .................... |
| .................... // Definice vlastnich fontu |
| .................... // |
| .................... // Vlastnich definic muze byt jen 8 do pozic 0 az 7 pameti CGRAM radice lcd displeje |
| .................... // Pro snadne definovani jsou pripraveny nasledujici definice a na konci souboru je uveden |
| .................... // priklad pouziti definovanych znaku. |
| .................... |
| .................... |
| .................... // Pomocna procedura pro posilani ridicich dat do radice displeje |
| .................... // |
| .................... void lcd_putc2(int Data) |
| .................... { |
| .................... lcd_send_byte(1,Data); |
| .................... } |
| .................... |
| .................... |
| .................... // Pomocne definice pro programovani obsahu CGRAM |
| .................... // |
| .................... #define lcd_define_start(Code) lcd_send_byte(0,0x40+(Code<<3)); delay_ms(2) |
| .................... #define lcd_define_def(String) printf(lcd_putc2,String); |
| .................... #define lcd_define_end() lcd_send_byte(0,3); delay_ms(2) |
| .................... |
| .................... |
| .................... // Vlastni vykonne makro pro definovani fontu do pozice Index CGRAM s definicnim retezcem Def |
| .................... // |
| .................... #define lcd_define_char(Index, Def) lcd_define_start(Index); lcd_define_def(Def); lcd_define_end(); |
| .................... |
| .................... |
| .................... // Pripravene definice fontu vybranych znaku |
| .................... // V tabulce nesmi byt 00 (konec retezce v printf()), misto toho davame 80 |
| .................... // |
| .................... #define LCD_CHAR_BAT100 "\x0E\x1F\x1F\x1F\x1F\x1F\x1F\x1F" /* symbol plne baterie */ |
| .................... #define LCD_CHAR_BAT50 "\x0E\x1F\x11\x11\x13\x17\x1F\x1F" /* symbol polovicni baterie */ |
| .................... #define LCD_CHAR_BAT0 "\x0E\x1F\x11\x11\x11\x11\x11\x1F" /* symbol vybite baterie */ |
| .................... #define LCD_CHAR_UP "\x80\x04\x0E\x15\x04\x04\x04\x80" /* symbol sipka nahoru */ |
| .................... #define LCD_CHAR_DOWN "\x80\x04\x04\x04\x15\x0E\x04\x80" /* symbol Sipka dolu */ |
| .................... #define LCD_CHAR_LUA "\x04\x0E\x11\x11\x1F\x11\x11\x80" /* A s carkou */ |
| .................... #define LCD_CHAR_LLA "\x01\x02\x0E\x01\x1F\x11\x0F\x80" /* a s carkou */ |
| .................... #define LCD_CHAR_HUC "\x0A\x0E\x11\x10\x10\x11\x0E\x80" /* C s hackem */ |
| .................... #define LCD_CHAR_HLC "\x0A\x04\x0E\x10\x10\x11\x0E\x80" /* c s hackem */ |
| .................... #define LCD_CHAR_HUD "\x0A\x1C\x12\x11\x11\x12\x1C\x80" /* D s hackem */ |
| .................... #define LCD_CHAR_HLD "\x05\x03\x0D\x13\x11\x11\x0F\x80" /* d s hackem */ |
| .................... #define LCD_CHAR_LUE "\x04\x1F\x10\x10\x1E\x10\x1F\x80" /* E s carkou */ |
| .................... #define LCD_CHAR_LLE "\x01\x02\x0E\x11\x1F\x10\x0E\x80" /* e s carkou */ |
| .................... #define LCD_CHAR_HUE "\x0A\x1F\x10\x1E\x10\x10\x1F\x80" /* E s hackem */ |
| .................... #define LCD_CHAR_HLE "\x0A\x04\x0E\x11\x1F\x10\x0E\x80" /* e s hackem */ |
| .................... #define LCD_CHAR_LUI "\x04\x0E\x04\x04\x04\x04\x0E\x80" /* I s carkou */ |
| .................... #define LCD_CHAR_LLI "\x02\x04\x80\x0C\x04\x04\x0E\x80" /* i s carkou */ |
| .................... #define LCD_CHAR_HUN "\x0A\x15\x11\x19\x15\x13\x11\x80" /* N s hackem */ |
| .................... #define LCD_CHAR_HLN "\x0A\x04\x16\x19\x11\x11\x11\x80" /* n s hackem */ |
| .................... #define LCD_CHAR_LUO "\x04\x0E\x11\x11\x11\x11\x0E\x80" /* O s carkou */ |
| .................... #define LCD_CHAR_LLO "\x02\x04\x0E\x11\x11\x11\x0E\x80" /* o s carkou */ |
| .................... #define LCD_CHAR_HUR "\x0A\x1E\x11\x1E\x14\x12\x11\x80" /* R s hackem */ |
| .................... #define LCD_CHAR_HLR "\x0A\x04\x16\x19\x10\x10\x10\x80" /* r s hackem */ |
| .................... #define LCD_CHAR_HUS "\x0A\x0F\x10\x0E\x01\x01\x1E\x80" /* S s hackem */ |
| .................... #define LCD_CHAR_HLS "\x0A\x04\x0E\x10\x0E\x01\x1E\x80" /* s s hackem */ |
| .................... #define LCD_CHAR_HUT "\x0A\x1F\x04\x04\x04\x04\x04\x80" /* T s hackem */ |
| .................... #define LCD_CHAR_HLT "\x0A\x0C\x1C\x08\x08\x09\x06\x80" /* t s hackem */ |
| .................... #define LCD_CHAR_LUU "\x02\x15\x11\x11\x11\x11\x0E\x80" /* U s carkou */ |
| .................... #define LCD_CHAR_LLU "\x02\x04\x11\x11\x11\x13\x0D\x80" /* u s carkou */ |
| .................... #define LCD_CHAR_CUU "\x06\x17\x11\x11\x11\x11\x0E\x80" /* U s krouzkem */ |
| .................... #define LCD_CHAR_CLU "\x06\x06\x11\x11\x11\x11\x0E\x80" /* u s krouzkem */ |
| .................... #define LCD_CHAR_LUY "\x02\x15\x11\x0A\x04\x04\x04\x80" /* Y s carkou */ |
| .................... #define LCD_CHAR_LLY "\x02\x04\x11\x11\x0F\x01\x0E\x80" /* y s carkou */ |
| .................... #define LCD_CHAR_HUZ "\x0A\x1F\x01\x02\x04\x08\x1F\x80" /* Z s hackem */ |
| .................... #define LCD_CHAR_HLZ "\x0A\x04\x1F\x02\x04\x08\x1F\x80" /* z s hackem */ |
| .................... |
| .................... |
| .................... // Priklad pouziti definovanych znaku |
| .................... // |
| .................... // |
| .................... //void lcd_sample() |
| .................... //{ |
| .................... // lcd_define_char(0,LCD_CHAR_BAT50); // Priklad definice znaku baterie do pozice 0 |
| .................... // lcd_define_char(2,LCD_CHAR_HLE LCD_CHAR_LUI); // Priklad definice znaku e s hackem a I s carkou od pozice 2 |
| .................... // // vsimnete si, ze neni carka mezi retezci s definici (oba retezce definuji |
| .................... // // jediny definicni retezec) |
| .................... // printf(lcd_putc,"\fZnaky:\20\22\23"); // priklad vypisu znaku z pozice 0, 2 a 3 |
| .................... // delay_ms(1000); |
| .................... // lcd_define_char(0,LCD_CHAR_BAT0); // Predefinovani tvaru znaku v pozici 0 |
| .................... // delay_ms(1000); |
| .................... //} |
| .................... |
| .................... |
| .................... void main() |
| .................... { |
| 00FC: CLRF 04 |
| 00FD: MOVLW 1F |
| 00FE: ANDWF 03,F |
| 00FF: BSF 03.5 |
| 0100: BSF 1F.0 |
| 0101: BSF 1F.1 |
| 0102: BSF 1F.2 |
| 0103: BCF 1F.3 |
| .................... |
| .................... setup_adc_ports(NO_ANALOGS); |
| * |
| 0107: BSF 03.5 |
| 0108: BSF 1F.0 |
| 0109: BSF 1F.1 |
| 010A: BSF 1F.2 |
| 010B: BCF 1F.3 |
| .................... setup_adc(ADC_OFF); |
| 010C: BCF 03.5 |
| 010D: BCF 1F.0 |
| .................... setup_psp(PSP_DISABLED); |
| 010E: BSF 03.5 |
| 010F: BCF 09.4 |
| .................... setup_spi(FALSE); |
| 0110: BCF 03.5 |
| 0111: BCF 14.5 |
| 0112: BCF 20.5 |
| 0113: MOVF 20,W |
| 0114: BSF 03.5 |
| 0115: MOVWF 07 |
| 0116: BCF 03.5 |
| 0117: BSF 20.4 |
| 0118: MOVF 20,W |
| 0119: BSF 03.5 |
| 011A: MOVWF 07 |
| 011B: BCF 03.5 |
| 011C: BCF 20.3 |
| 011D: MOVF 20,W |
| 011E: BSF 03.5 |
| 011F: MOVWF 07 |
| 0120: MOVLW 00 |
| 0121: BCF 03.5 |
| 0122: MOVWF 14 |
| 0123: BSF 03.5 |
| 0124: MOVWF 14 |
| .................... setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
| 0125: MOVF 01,W |
| 0126: ANDLW C7 |
| 0127: IORLW 08 |
| 0128: MOVWF 01 |
| .................... setup_timer_1(T1_DISABLED); |
| 0129: BCF 03.5 |
| 012A: CLRF 10 |
| .................... setup_timer_2(T2_DISABLED,0,1); |
| 012B: MOVLW 00 |
| 012C: MOVWF 78 |
| 012D: MOVWF 12 |
| 012E: MOVLW 00 |
| 012F: BSF 03.5 |
| 0130: MOVWF 12 |
| .................... |
| .................... lcd_init(); |
| 0131: BCF 03.5 |
| 0132: GOTO 07D |
| .................... |
| .................... while(true); |
| 0133: GOTO 133 |
| .................... { |
| .................... Delay_ms(100); |
| 0134: MOVLW 64 |
| 0135: MOVWF 23 |
| 0136: CALL 026 |
| .................... |
| .................... LCD_gotoxy(1,1); |
| 0137: MOVLW 01 |
| 0138: MOVWF 23 |
| 0139: MOVWF 24 |
| 013A: CALL 0B6 |
| .................... printf(lcd_putc,"Ahoj, Display funguje"); |
| 013B: CLRF 21 |
| 013C: MOVF 21,W |
| 013D: CALL 00C |
| 013E: IORLW 00 |
| 013F: BTFSC 03.2 |
| 0140: GOTO 145 |
| 0141: INCF 21,F |
| 0142: MOVWF 22 |
| 0143: GOTO 0C7 |
| 0144: GOTO 13C |
| .................... } |
| .................... |
| .................... } |
| 0145: SLEEP |
| Configuration Fuses: |
| Word 1: 3F39 XT NOWDT NOPUT NOPROTECT NOBROWNOUT NOLVP NOCPD NOWRT NODEBUG |
| /programy/C/PIC/test/C16F876A/LCD/main.sta |
|---|
| 0,0 → 1,39 |
| ROM used: 326 (4%) |
| 326 (4%) including unused fragments |
| 1 Average locations per line |
| 5 Average locations per statement |
| RAM used: 7 (4%) at main() level |
| 15 (9%) worst case |
| Lines Stmts % Files |
| ----- ----- --- ----- |
| 35 14 22 C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\main.c |
| 16 0 0 C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\main.h |
| 280 0 0 Z:\home\kaklik\%SystemDrive%\Program Files\PICC\devices\16F877.h |
| 312 49 64 C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\LCD.C |
| ----- ----- |
| 1286 126 Total |
| Page ROM % RAM Functions: |
| ---- --- --- --- ---------- |
| 0 21 6 1 @delay_ms1 |
| 0 8 2 0 @const36 |
| 0 42 13 1 lcd_send_nibble |
| 0 24 7 2 lcd_send_byte |
| 0 57 17 2 lcd_init |
| 0 17 5 4 lcd_gotoxy |
| 0 53 16 1 lcd_putc |
| 0 74 23 1 main |
| 0 26 8 0 @const10117 |
| Segment Used Free |
| --------- ---- ---- |
| 00000-00003 4 0 |
| 00004-007FF 322 1722 |
| 00800-00FFF 0 2048 |
| 01000-017FF 0 2048 |
| 01800-01FFF 0 2048 |
| /programy/C/PIC/test/C16F876A/LCD/main.sym |
|---|
| 0,0 → 1,62 |
| 008 PSP_DATA |
| 015-016 CCP_1 |
| 015 CCP_1_LOW |
| 016 CCP_1_HIGH |
| 01B CCP_2_LOW |
| 01B-01C CCP_2 |
| 01C CCP_2_HIGH |
| 020 @TRIS_C |
| 021 lcd_init.i |
| 021 main.@SCRATCH |
| 022 lcd_putc.c |
| 022 lcd_init.@SCRATCH |
| 023 @delay_ms1.P1 |
| 023 lcd_gotoxy.x |
| 024 lcd_gotoxy.y |
| 025 lcd_gotoxy.Adr |
| 026 lcd_gotoxy.@SCRATCH |
| 027 lcd_send_byte.Adr |
| 028 lcd_send_byte.n |
| 029 lcd_send_nibble.n |
| 077 @SCRATCH |
| 078 @SCRATCH |
| 078 _RETURN_ |
| 079 @SCRATCH |
| 07A @SCRATCH |
| 07B @SCRATCH |
| 0026 @delay_ms1 |
| 0004 @const36 |
| 003B lcd_send_nibble |
| 0065 lcd_send_byte |
| 007D lcd_init |
| 00B6 lcd_gotoxy |
| 00C7 lcd_putc |
| 00FC main |
| 000C @const10117 |
| 00FC @cinit |
| Project Files: |
| C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\main.c |
| C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\main.h |
| Z:\home\kaklik\%SystemDrive%\Program Files\PICC\devices\16F877.h |
| C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\LCD.C |
| Units: |
| C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\main.c (main) |
| Compiler Settings: |
| Processor: PIC16F877 |
| Pointer Size: 8 |
| ADC Range: 0-255 |
| Opt Level: 9 |
| Short,Int,Long: 1,8,16 |
| Output Files: |
| Errors: C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\main.err |
| INHX8: C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\main.hex |
| Symbols: C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\main.sym |
| List: C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\main.lst |
| Debug/COFF: C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\main.cof |
| Call Tree: C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\main.tre |
| Statistics: C:\windows\profiles\kaklik\My Documents\projekty\programy\C\PIC_C\test\C16F876A\LCD\main.sta |
| /programy/C/PIC/test/C16F876A/LCD/main.tre |
|---|
| 0,0 → 1,38 |
| ÀÄmain |
| ÀÄmain 0/74 Ram=1 |
| ÃÄ??0?? |
| ÃÄlcd_init 0/57 Ram=2 |
| ³ ÃÄ@delay_ms1 0/21 Ram=1 |
| ³ ÃÄ@delay_ms1 0/21 Ram=1 |
| ³ ÃÄlcd_send_nibble 0/42 Ram=1 |
| ³ ÃÄlcd_send_nibble 0/42 Ram=1 |
| ³ ÃÄ@const36 0/8 Ram=0 |
| ³ ÃÄlcd_send_byte 0/24 Ram=2 |
| ³ ³ ÃÄlcd_send_nibble 0/42 Ram=1 |
| ³ ³ ÀÄlcd_send_nibble 0/42 Ram=1 |
| ³ ÀÄ@delay_ms1 0/21 Ram=1 |
| ÃÄ@delay_ms1 0/21 Ram=1 |
| ÃÄlcd_gotoxy 0/17 Ram=4 |
| ³ ÀÄlcd_send_byte 0/24 Ram=2 |
| ³ ÃÄlcd_send_nibble 0/42 Ram=1 |
| ³ ÀÄlcd_send_nibble 0/42 Ram=1 |
| ÃÄ@const10117 0/26 Ram=0 |
| ÀÄlcd_putc 0/53 Ram=1 |
| ÃÄlcd_send_byte 0/24 Ram=2 |
| ³ ÃÄlcd_send_nibble 0/42 Ram=1 |
| ³ ÀÄlcd_send_nibble 0/42 Ram=1 |
| ÃÄ@delay_ms1 0/21 Ram=1 |
| ÃÄlcd_gotoxy 0/17 Ram=4 |
| ³ ÀÄlcd_send_byte 0/24 Ram=2 |
| ³ ÃÄlcd_send_nibble 0/42 Ram=1 |
| ³ ÀÄlcd_send_nibble 0/42 Ram=1 |
| ÃÄlcd_gotoxy 0/17 Ram=4 |
| ³ ÀÄlcd_send_byte 0/24 Ram=2 |
| ³ ÃÄlcd_send_nibble 0/42 Ram=1 |
| ³ ÀÄlcd_send_nibble 0/42 Ram=1 |
| ÃÄlcd_send_byte 0/24 Ram=2 |
| ³ ÃÄlcd_send_nibble 0/42 Ram=1 |
| ³ ÀÄlcd_send_nibble 0/42 Ram=1 |
| ÀÄlcd_send_byte 0/24 Ram=2 |
| ÃÄlcd_send_nibble 0/42 Ram=1 |
| ÀÄlcd_send_nibble 0/42 Ram=1 |
| /programy/C/PIC/test/PIC16F88/blik/blik.BAK |
|---|
| 0,0 → 1,44 |
| #include "blik.h" |
| void main() |
| { |
| int i; |
| setup_adc_ports(NO_ANALOGS|VSS_VDD); // parametry |
| setup_adc(ADC_OFF); |
| setup_spi(FALSE); |
| setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
| setup_timer_1(T1_DISABLED); |
| setup_timer_2(T2_DISABLED,0,1); |
| setup_comparator(NC_NC_NC_NC); |
| setup_vref(FALSE); |
| setup_oscillator(False); |
| while(true) // nekonecny cyklus |
| { |
| output_high(PIN_A4); // nastav B0 na 1 |
| Delay_ms(50); // pockej 50ms |
| output_high(PIN_B1); // nastav B0 na 1 |
| Delay_ms(50); // pockej 50ms |
| output_high(PIN_B2); // nastav B0 na 1 |
| for(i=0;i<=100;i++) |
| { |
| Output_high(PIN_A2); |
| Delay_ms(1); |
| Output_low(PIN_A2); |
| Delay_ms(1); |
| } |
| output_low(PIN_A4); //nastav B0 na 0 |
| Delay_ms(50); // pockej 50ms |
| output_low(PIN_B1); //nastav B0 na 0 |
| Delay_ms(50); // pockej 50ms |
| output_low(PIN_B2); //nastav B0 na 0 |
| Delay_ms(50); // pockej 50ms |
| } // opakuj cyklus |
| } |
| /programy/C/PIC/test/PIC16F88/blik/blik.cof |
|---|
| Cannot display: file marked as a binary type. |
| svn:mime-type = application/octet-stream |
| Property changes: |
| Added: svn:mime-type |
| +application/octet-stream |
| \ No newline at end of property |
| /programy/C/PIC/test/PIC16F88/blik/blik.lst |
|---|
| 0,0 → 1,218 |
| CCS PCM C Compiler, Version 3.245, 27853 24-III-08 00:27 |
| Filename: D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F88\blik\blik.lst |
| ROM used: 136 words (3%) |
| Largest free fragment is 2048 |
| RAM used: 6 (3%) at main() level |
| 6 (3%) worst case |
| Stack: 0 locations |
| * |
| 0000: MOVLW 00 |
| 0001: MOVWF 0A |
| 0002: GOTO 004 |
| 0003: NOP |
| .................... #include "blik.h" |
| .................... #include <16F88.h> |
| .................... //////// Standard Header file for the PIC16F88 device //////////////// |
| .................... #device PIC16F88 |
| .................... #list |
| .................... |
| .................... #device adc=8 |
| .................... |
| .................... #FUSES NOWDT //No Watch Dog Timer |
| .................... #FUSES INTRC //Crystal osc <= 4mhz |
| .................... #FUSES NOPUT //No Power Up Timer |
| .................... #FUSES NOMCLR //Master Clear pin used for I/O |
| .................... #FUSES NOBROWNOUT //No brownout reset |
| .................... #FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O |
| .................... #FUSES NOCPD //No EE protection |
| .................... #FUSES NOWRT //Program memory not write protected |
| .................... #FUSES NODEBUG //No Debug mode for ICD |
| .................... #FUSES NOPROTECT //Code not protected from reading |
| .................... #FUSES NOFCMEN //Fail-safe clock monitor disabled |
| .................... #FUSES NOIESO //Internal External Switch Over mode disabled |
| .................... |
| .................... #use delay(clock=37526) |
| .................... |
| .................... |
| .................... |
| .................... |
| .................... void main() |
| .................... { |
| 0004: CLRF 04 |
| 0005: MOVLW 1F |
| 0006: ANDWF 03,F |
| 0007: BSF 03.5 |
| 0008: BCF 1F.4 |
| 0009: BCF 1F.5 |
| 000A: MOVF 1B,W |
| 000B: ANDLW 80 |
| 000C: MOVWF 1B |
| 000D: MOVLW 07 |
| 000E: MOVWF 1C |
| .................... |
| .................... int i; |
| .................... |
| .................... setup_adc_ports(NO_ANALOGS|VSS_VDD); // parametry |
| 000F: BCF 1F.4 |
| 0010: BCF 1F.5 |
| 0011: MOVF 1B,W |
| 0012: ANDLW 80 |
| 0013: MOVWF 1B |
| .................... setup_adc(ADC_OFF); |
| 0014: BCF 03.5 |
| 0015: BCF 1F.0 |
| .................... setup_spi(FALSE); |
| 0016: BCF 14.5 |
| 0017: BSF 03.5 |
| 0018: BCF 06.2 |
| 0019: BSF 06.1 |
| 001A: BCF 06.4 |
| 001B: MOVLW 00 |
| 001C: BCF 03.5 |
| 001D: MOVWF 14 |
| 001E: BSF 03.5 |
| 001F: MOVWF 14 |
| .................... setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
| 0020: MOVF 01,W |
| 0021: ANDLW C7 |
| 0022: IORLW 08 |
| 0023: MOVWF 01 |
| .................... setup_timer_1(T1_DISABLED); |
| 0024: BCF 03.5 |
| 0025: CLRF 10 |
| .................... setup_timer_2(T2_DISABLED,0,1); |
| 0026: MOVLW 00 |
| 0027: MOVWF 78 |
| 0028: MOVWF 12 |
| 0029: MOVLW 00 |
| 002A: BSF 03.5 |
| 002B: MOVWF 12 |
| .................... setup_comparator(NC_NC_NC_NC); |
| 002C: MOVLW 07 |
| 002D: MOVWF 1C |
| 002E: MOVF 1C,W |
| 002F: BCF 03.5 |
| 0030: BCF 0D.6 |
| .................... setup_vref(FALSE); |
| 0031: BSF 03.5 |
| 0032: CLRF 1D |
| .................... setup_oscillator(False); |
| 0033: CLRF 0F |
| 0034: MOVF 0F,W |
| .................... |
| .................... while(true) // nekonecny cyklus |
| .................... { |
| .................... output_high(PIN_B0); // nastav B0 na 1 |
| 0035: BCF 06.0 |
| 0036: BCF 03.5 |
| 0037: BSF 06.0 |
| .................... Delay_ms(50); // pockej 50ms |
| 0038: MOVLW 99 |
| 0039: MOVWF 77 |
| 003A: DECFSZ 77,F |
| 003B: GOTO 03A |
| 003C: NOP |
| 003D: NOP |
| .................... output_high(PIN_B1); // nastav B0 na 1 |
| 003E: BSF 03.5 |
| 003F: BCF 06.1 |
| 0040: BCF 03.5 |
| 0041: BSF 06.1 |
| .................... Delay_ms(50); // pockej 50ms |
| 0042: MOVLW 99 |
| 0043: MOVWF 77 |
| 0044: DECFSZ 77,F |
| 0045: GOTO 044 |
| 0046: NOP |
| 0047: NOP |
| .................... output_high(PIN_B2); // nastav B0 na 1 |
| 0048: BSF 03.5 |
| 0049: BCF 06.2 |
| 004A: BCF 03.5 |
| 004B: BSF 06.2 |
| .................... |
| .................... for(i=0;i<=100;i++) |
| 004C: CLRF 21 |
| 004D: MOVF 21,W |
| 004E: SUBLW 64 |
| 004F: BTFSS 03.0 |
| 0050: GOTO 067 |
| .................... { |
| .................... |
| .................... Output_high(PIN_A2); |
| 0051: BSF 03.5 |
| 0052: BCF 05.2 |
| 0053: BCF 03.5 |
| 0054: BSF 05.2 |
| .................... Delay_ms(1); |
| 0055: MOVLW 02 |
| 0056: MOVWF 77 |
| 0057: DECFSZ 77,F |
| 0058: GOTO 057 |
| 0059: NOP |
| 005A: NOP |
| .................... Output_low(PIN_A2); |
| 005B: BSF 03.5 |
| 005C: BCF 05.2 |
| 005D: BCF 03.5 |
| 005E: BCF 05.2 |
| .................... Delay_ms(1); |
| 005F: MOVLW 02 |
| 0060: MOVWF 77 |
| 0061: DECFSZ 77,F |
| 0062: GOTO 061 |
| 0063: NOP |
| 0064: NOP |
| .................... } |
| 0065: INCF 21,F |
| 0066: GOTO 04D |
| .................... |
| .................... output_low(PIN_B0); //nastav B0 na 0 |
| 0067: BSF 03.5 |
| 0068: BCF 06.0 |
| 0069: BCF 03.5 |
| 006A: BCF 06.0 |
| .................... Delay_ms(50); // pockej 50ms |
| 006B: MOVLW 99 |
| 006C: MOVWF 77 |
| 006D: DECFSZ 77,F |
| 006E: GOTO 06D |
| 006F: NOP |
| 0070: NOP |
| .................... output_low(PIN_B1); //nastav B0 na 0 |
| 0071: BSF 03.5 |
| 0072: BCF 06.1 |
| 0073: BCF 03.5 |
| 0074: BCF 06.1 |
| .................... Delay_ms(50); // pockej 50ms |
| 0075: MOVLW 99 |
| 0076: MOVWF 77 |
| 0077: DECFSZ 77,F |
| 0078: GOTO 077 |
| 0079: NOP |
| 007A: NOP |
| .................... output_low(PIN_B2); //nastav B0 na 0 |
| 007B: BSF 03.5 |
| 007C: BCF 06.2 |
| 007D: BCF 03.5 |
| 007E: BCF 06.2 |
| .................... Delay_ms(50); // pockej 50ms |
| 007F: MOVLW 99 |
| 0080: MOVWF 77 |
| 0081: DECFSZ 77,F |
| 0082: GOTO 081 |
| 0083: NOP |
| 0084: NOP |
| .................... } // opakuj cyklus |
| 0085: BSF 03.5 |
| 0086: GOTO 035 |
| .................... |
| .................... } |
| 0087: SLEEP |
| Configuration Fuses: |
| Word 1: 3F19 NOWDT NOPUT NOMCLR NOBROWNOUT NOLVP NOCPD NOWRT NODEBUG CCPB0 NOPROTECT INTRC |
| Word 2: 3FFC NOFCMEN NOIESO |
| /programy/C/PIC/test/PIC16F88/blik/blik.PJT |
|---|
| 0,0 → 1,42 |
| [PROJECT] |
| Target=blik.HEX |
| Development_Mode= |
| Processor=0x688F |
| ToolSuite=CCS |
| Processor_Text=PIC16F88 |
| [Directories] |
| Include=C:\Program Files\PICC\devices\;C:\Program Files\PICC\dr |
| Library= |
| LinkerScript= |
| [Target Data] |
| FileList=D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F88\blik\blik.c |
| BuildTool=C-COMPILER |
| OptionString=+FM |
| AdditionalOptionString= |
| BuildRequired=1 |
| [blik.c] |
| Type=4 |
| Path= |
| FileList= |
| BuildTool= |
| OptionString= |
| AdditionalOptionString= |
| [mru-list] |
| 1=blik.c |
| [Windows] |
| 0=0000 blik.c 0 0 796 451 3 0 |
| [Opened Files] |
| 1=D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F88\blik\blik.c |
| 2=D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F88\blik\blik.h |
| 3=C:\Program Files\PICC\devices\16F88.h |
| 4= |
| 5= |
| [Units] |
| Count=1 |
| 1=D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F88\blik\blik.c (main) |
| /programy/C/PIC/test/PIC16F88/blik/blik.c |
|---|
| 0,0 → 1,44 |
| #include "blik.h" |
| void main() |
| { |
| int i; |
| setup_adc_ports(NO_ANALOGS|VSS_VDD); // parametry |
| setup_adc(ADC_OFF); |
| setup_spi(FALSE); |
| setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
| setup_timer_1(T1_DISABLED); |
| setup_timer_2(T2_DISABLED,0,1); |
| setup_comparator(NC_NC_NC_NC); |
| setup_vref(FALSE); |
| setup_oscillator(False); |
| while(true) // nekonecny cyklus |
| { |
| output_high(PIN_B0); // nastav B0 na 1 |
| Delay_ms(50); // pockej 50ms |
| output_high(PIN_B1); // nastav B0 na 1 |
| Delay_ms(50); // pockej 50ms |
| output_high(PIN_B2); // nastav B0 na 1 |
| for(i=0;i<=100;i++) |
| { |
| Output_high(PIN_A2); |
| Delay_ms(1); |
| Output_low(PIN_A2); |
| Delay_ms(1); |
| } |
| output_low(PIN_B0); //nastav B0 na 0 |
| Delay_ms(50); // pockej 50ms |
| output_low(PIN_B1); //nastav B0 na 0 |
| Delay_ms(50); // pockej 50ms |
| output_low(PIN_B2); //nastav B0 na 0 |
| Delay_ms(50); // pockej 50ms |
| } // opakuj cyklus |
| } |
| /programy/C/PIC/test/PIC16F88/blik/blik.sta |
|---|
| 0,0 → 1,28 |
| ROM used: 136 (3%) |
| 136 (3%) including unused fragments |
| 0 Average locations per line |
| 5 Average locations per statement |
| RAM used: 6 (3%) at main() level |
| 6 (3%) worst case |
| Lines Stmts % Files |
| ----- ----- --- ----- |
| 45 28 100 D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F88\blik\blik.c |
| 19 0 0 D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F88\blik\blik.h |
| 279 0 0 C:\Program Files\PICC\devices\16F88.h |
| ----- ----- |
| 686 56 Total |
| Page ROM % RAM Functions: |
| ---- --- --- --- ---------- |
| 0 132 97 1 main |
| Segment Used Free |
| --------- ---- ---- |
| 00000-00003 4 0 |
| 00004-007FF 132 1912 |
| 00800-00FFF 0 2048 |
| /programy/C/PIC/test/PIC16F88/blik/blik.h |
|---|
| 0,0 → 1,18 |
| #include <16F88.h> |
| #device adc=8 |
| #FUSES NOWDT //No Watch Dog Timer |
| #FUSES INTRC //Crystal osc <= 4mhz |
| #FUSES NOPUT //No Power Up Timer |
| #FUSES NOMCLR //Master Clear pin used for I/O |
| #FUSES NOBROWNOUT //No brownout reset |
| #FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O |
| #FUSES NOCPD //No EE protection |
| #FUSES NOWRT //Program memory not write protected |
| #FUSES NODEBUG //No Debug mode for ICD |
| #FUSES NOPROTECT //Code not protected from reading |
| #FUSES NOFCMEN //Fail-safe clock monitor disabled |
| #FUSES NOIESO //Internal External Switch Over mode disabled |
| #use delay(clock=37526) |
| /programy/C/PIC/test/PIC16F88/blik/blik.hex |
|---|
| 0,0 → 1,20 |
| :1000000000308A000428000084011F308305831615 |
| :100010001F129F121B0880399B0007309C001F1283 |
| :100020009F121B0880399B0083121F1094128316A5 |
| :100030000611861406120030831294008316940071 |
| :100040000108C73908388100831290010030F80098 |
| :10005000920000308316920007309C001C08831227 |
| :100060000D1383169D018F010F08061083120614CD |
| :100070009930F700F70B3A2800000000831686102D |
| :10008000831286149930F700F70B44280000000013 |
| :100090008316061183120615A1012108643C031C76 |
| :1000A000672883160511831205150230F700F70B38 |
| :1000B0005728000000008316051183120511023035 |
| :1000C000F700F70B612800000000A10A4D288316F5 |
| :1000D0000610831206109930F700F70B6D28000008 |
| :1000E000000083168610831286109930F700F70BF4 |
| :1000F000772800000000831606118312061199303C |
| :10010000F700F70B812800000000831635286300F4 |
| :04400E00193FFC3F1B |
| :00000001FF |
| ;PIC16F88 |
| /programy/C/PIC/test/PIC16F88/blik/blik.sym |
|---|
| 0,0 → 1,39 |
| 015 CCP_1_LOW |
| 015-016 CCP_1 |
| 016 CCP_1_HIGH |
| 021 main.i |
| 077 @SCRATCH |
| 078 @SCRATCH |
| 078 _RETURN_ |
| 079 @SCRATCH |
| 07A @SCRATCH |
| 07B @SCRATCH |
| 09C.6 C1OUT |
| 09C.7 C2OUT |
| 0004 main |
| 0004 @cinit |
| Project Files: |
| D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F88\blik\blik.c |
| D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F88\blik\blik.h |
| C:\Program Files\PICC\devices\16F88.h |
| Units: |
| D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F88\blik\blik.c (main) |
| Compiler Settings: |
| Processor: PIC16F88 |
| Pointer Size: 8 |
| ADC Range: 0-255 |
| Opt Level: 9 |
| Short,Int,Long: 1,8,16 |
| Output Files: |
| Errors: D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F88\blik\blik.err |
| INHX8: D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F88\blik\blik.hex |
| Symbols: D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F88\blik\blik.sym |
| List: D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F88\blik\blik.lst |
| Debug/COFF: D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F88\blik\blik.cof |
| Call Tree: D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F88\blik\blik.tre |
| Statistics: D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F88\blik\blik.sta |
| /programy/C/PIC/test/PIC16F88/blik/blik.tre |
|---|
| 0,0 → 1,3 |
| ÀÄblik |
| ÀÄmain 0/132 Ram=1 |
| ÀÄ??0?? |
| /programy/C/PIC/test/PIC16F88/blik/blik.err |
|---|
| 0,0 → 1,2 |
| No Errors |
| 0 Errors, 0 Warnings. |
| /programy/C/PIC/test/PIC16F88/blik/prg.bat |
|---|
| 0,0 → 1,6 |
| call picpgr stop LPT2 |
| call picpgr erase pic16f88 LPT2 |
| call picpgr program blik.hex hex pic16f88 LPT2 |
| call picpgr run LPT2 |
| pause |
| call picpgr stop LPT2 |
| /programy/C/PIC/test/PIC16F84/blik/blik.PJT |
|---|
| 0,0 → 1,38 |
| [PROJECT] |
| Target=blik.HEX |
| Development_Mode= |
| Processor=0x6F84 |
| ToolSuite=CCS |
| [Directories] |
| Include=C:\Program Files\PICC\devices\;C:\Program Files\PICC\dr |
| Library= |
| LinkerScript= |
| [Target Data] |
| FileList=D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F84\blik\blik.c |
| BuildTool=C-COMPILER |
| OptionString=+FM |
| AdditionalOptionString= |
| BuildRequired=1 |
| [blik.c] |
| Type=4 |
| Path= |
| FileList= |
| BuildTool= |
| OptionString= |
| AdditionalOptionString= |
| [mru-list] |
| 1=blik.c |
| [Windows] |
| 0=0000 blik.c 0 0 796 451 3 0 |
| [Opened Files] |
| 1=D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F84\blik\blik.c |
| 2= |
| [Units] |
| Count=1 |
| 1=D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F84\blik\blik.c (main) |
| /programy/C/PIC/test/PIC16F84/blik/blik.cof |
|---|
| Cannot display: file marked as a binary type. |
| svn:mime-type = application/octet-stream |
| Property changes: |
| Added: svn:mime-type |
| +application/octet-stream |
| \ No newline at end of property |
| /programy/C/PIC/test/PIC16F84/blik/blik.lst |
|---|
| 0,0 → 1,98 |
| CCS PCM C Compiler, Version 3.245, 27853 23-III-08 21:00 |
| Filename: D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F84\blik\blik.lst |
| ROM used: 53 words (5%) |
| Largest free fragment is 971 |
| RAM used: 3 (4%) at main() level |
| 4 (6%) worst case |
| Stack: 1 locations |
| * |
| 0000: MOVLW 00 |
| 0001: MOVWF 0A |
| 0002: GOTO 019 |
| 0003: NOP |
| .................... #include "blik.h" |
| .................... #include <16F84A.h> |
| .................... //////// Standard Header file for the PIC16F84A device //////////////// |
| .................... #device PIC16F84A |
| .................... #list |
| .................... |
| .................... |
| .................... #FUSES NOWDT //No Watch Dog Timer |
| .................... #FUSES XT //Crystal osc <= 4mhz |
| .................... #FUSES NOPUT //No Power Up Timer |
| .................... #FUSES NOPROTECT //Code not protected from reading |
| .................... |
| .................... #use delay(clock=4000000) |
| 0004: MOVLW 10 |
| 0005: MOVWF 04 |
| 0006: MOVF 00,W |
| 0007: BTFSC 03.2 |
| 0008: GOTO 018 |
| 0009: MOVLW 01 |
| 000A: MOVWF 0D |
| 000B: CLRF 0C |
| 000C: DECFSZ 0C,F |
| 000D: GOTO 00C |
| 000E: DECFSZ 0D,F |
| 000F: GOTO 00B |
| 0010: MOVLW 4A |
| 0011: MOVWF 0C |
| 0012: DECFSZ 0C,F |
| 0013: GOTO 012 |
| 0014: NOP |
| 0015: NOP |
| 0016: DECFSZ 00,F |
| 0017: GOTO 009 |
| 0018: RETLW 00 |
| .................... |
| .................... |
| .................... |
| .................... |
| .................... void main() |
| .................... { |
| 0019: CLRF 04 |
| 001A: MOVLW 1F |
| 001B: ANDWF 03,F |
| .................... |
| .................... setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
| 001C: BSF 03.5 |
| 001D: MOVF 01,W |
| 001E: ANDLW C7 |
| 001F: IORLW 08 |
| 0020: MOVWF 01 |
| .................... |
| .................... while(true) |
| .................... { |
| .................... output_high(PIN_B0); |
| 0021: BCF 06.0 |
| 0022: BCF 03.5 |
| 0023: BSF 06.0 |
| .................... Delay_ms(700); |
| 0024: MOVLW 04 |
| 0025: MOVWF 0F |
| 0026: MOVLW AF |
| 0027: MOVWF 10 |
| 0028: CALL 004 |
| 0029: DECFSZ 0F,F |
| 002A: GOTO 026 |
| .................... output_low(PIN_B0); |
| 002B: BSF 03.5 |
| 002C: BCF 06.0 |
| 002D: BCF 03.5 |
| 002E: BCF 06.0 |
| .................... Delay_ms(50); |
| 002F: MOVLW 32 |
| 0030: MOVWF 10 |
| 0031: CALL 004 |
| .................... } |
| 0032: BSF 03.5 |
| 0033: GOTO 021 |
| .................... |
| .................... } |
| 0034: SLEEP |
| Configuration Fuses: |
| Word 1: 3FF9 XT NOWDT NOPUT NOPROTECT |
| /programy/C/PIC/test/PIC16F84/blik/blik.sta |
|---|
| 0,0 → 1,28 |
| ROM used: 53 (5%) |
| 53 (5%) including unused fragments |
| 0 Average locations per line |
| 8 Average locations per statement |
| RAM used: 3 (4%) at main() level |
| 4 (6%) worst case |
| Lines Stmts % Files |
| ----- ----- --- ----- |
| 18 7 100 D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F84\blik\blik.c |
| 10 0 0 D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F84\blik\blik.h |
| 113 0 0 C:\Program Files\PICC\devices\16F84A.h |
| ----- ----- |
| 282 14 Total |
| Page ROM % RAM Functions: |
| ---- --- --- --- ---------- |
| 0 21 40 1 @delay_ms1 |
| 0 28 53 1 main |
| Segment Used Free |
| --------- ---- ---- |
| 00000-00003 4 0 |
| 00004-003FF 49 971 |
| /programy/C/PIC/test/PIC16F84/blik/blik.sym |
|---|
| 0,0 → 1,32 |
| 00C @SCRATCH |
| 00D @SCRATCH |
| 00D _RETURN_ |
| 00F main.@SCRATCH |
| 010 @delay_ms1.P1 |
| 0004 @delay_ms1 |
| 0019 main |
| 0019 @cinit |
| Project Files: |
| D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F84\blik\blik.c |
| D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F84\blik\blik.h |
| C:\Program Files\PICC\devices\16F84A.h |
| Units: |
| D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F84\blik\blik.c (main) |
| Compiler Settings: |
| Processor: PIC16F84A |
| Pointer Size: 8 |
| Opt Level: 9 |
| Short,Int,Long: 1,8,16 |
| Output Files: |
| Errors: D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F84\blik\blik.err |
| INHX8: D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F84\blik\blik.hex |
| Symbols: D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F84\blik\blik.sym |
| List: D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F84\blik\blik.lst |
| Debug/COFF: D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F84\blik\blik.cof |
| Call Tree: D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F84\blik\blik.tre |
| Statistics: D:\KAKLIK\projekty\programy\C\PIC_C\test\PIC16F84\blik\blik.sta |
| /programy/C/PIC/test/PIC16F84/blik/blik.BAK |
|---|
| 0,0 → 1,9 |
| #include "blik.h" |
| void main() |
| { |
| setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
| } |
| /programy/C/PIC/test/PIC16F84/blik/blik.c |
|---|
| 0,0 → 1,17 |
| #include "blik.h" |
| void main() |
| { |
| setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
| while(true) |
| { |
| output_high(PIN_B0); |
| Delay_ms(700); |
| output_low(PIN_B0); |
| Delay_ms(50); |
| } |
| } |
| /programy/C/PIC/test/PIC16F84/blik/blik.err |
|---|
| 0,0 → 1,2 |
| No Errors |
| 0 Errors, 0 Warnings. |
| /programy/C/PIC/test/PIC16F84/blik/blik.h |
|---|
| 0,0 → 1,9 |
| #include <16F84A.h> |
| #FUSES NOWDT //No Watch Dog Timer |
| #FUSES XT //Crystal osc <= 4mhz |
| #FUSES NOPUT //No Power Up Timer |
| #FUSES NOPROTECT //Code not protected from reading |
| #use delay(clock=4000000) |
| /programy/C/PIC/test/PIC16F84/blik/blik.hex |
|---|
| 0,0 → 1,10 |
| :1000000000308A001928000010308400000803190D |
| :10001000182801308D008C018C0B0C288D0B0B28BF |
| :100020004A308C008C0B122800000000800B09283D |
| :10003000003484011F30830583160108C73908384E |
| :10004000810006108312061404308F00AF30900038 |
| :1000500004208F0B262883160610831206103230D8 |
| :0A006000900004208316212863009D |
| :02400E00F93F78 |
| :00000001FF |
| ;PIC16F84A |
| /programy/C/PIC/test/PIC16F84/blik/blik.tre |
|---|
| 0,0 → 1,5 |
| ÀÄblik |
| ÀÄmain 0/28 Ram=1 |
| ÃÄ??0?? |
| ÃÄ@delay_ms1 0/21 Ram=1 |
| ÀÄ@delay_ms1 0/21 Ram=1 |
| /programy/C/PIC/test/PIC16F84/blik/prg.bat |
|---|
| 0,0 → 1,6 |
| call picpgr stop LPT2 |
| call picpgr erase pic16f84a LPT2 |
| call picpgr program blik.hex hex pic16f84a LPT2 |
| call picpgr run LPT2 |
| pause |
| call picpgr stop LPT2 |